參數資料
型號: CS5156
廠商: ZF Electronics Corporation
英文描述: CPU 5-Bit Nonsynchronous Buck Controller
中文描述: CPU的5位非同步降壓控制器
文件頁數: 10/14頁
文件大小: 308K
代理商: CS5156
Applications Information: continued
C
10
External Output Enable Circuit
On/off control of the regulator can be implemented
through two additional discrete components (see Figure 12).
This circuit operates by pulling the soft start pin high, and
the V
FFB
pin low, emulating a short circuit condition.
Figure 12: Implementing shutdown with the CS5156.
External Power Good Circuit
An optional Power Good signal can be generated through
the use of four additional external components (see Figure
15). The threshold voltage of the Power Good signal can be
adjusted per the following equation:
V
Power Good
=
This circuit provides an open collector output that drives
the Power Good output to ground for regulator voltages
less than V
Power Good
.
Figure 13: Implementing Power Good with the CS5156.
Figure 14: CS5156 demonstration board during power up. Power Good
signal is activated when output voltage reaches 1.70V.
Selecting External Components
The CS5156 can be used with a wide range of external
power components to optimize the cost and performance of
a particular design. The following information can be used
as general guidelines to assist in their selection.
NFET Power Transistors
Both logic level and standard MOSFETs can be used. The
reference designs derive gate drive from the 12V supply
which is generally available in most computer systems and
use logic level MOSFETs. A charge pump may be easily
implemented to support 5V only systems. Multiple
MOSFETs may be paralleled to reduce losses and improve
efficiency and thermal management.
Voltage applied to the MOSFET gate depends on the appli-
cation circuit used. The gate driver output is specified to
drive to within 1.5V of ground when in the low state and to
within 2V of its bias supply when in the high state. In prac-
tice, the MOSFET gate will be driven rail to rail due to
overshoot caused by the capacitive load it presents to the
controller IC. For the typical application where V
CC1
= V
CC2
= 12V and 5V is used as the source for the regulator output
current, the following gate drive is provided;
V
GATE
= 12V - 5V = 7V (see Figure 15).
Trace 3 = 12V Input (V
) and V
CC2
) (10V/div.)
Trace 4 = 5V Input (2V/div.)
Trace 1 = Regulator Output Voltage (1V/div.)
Trace 2 = Power Good Signal (2V/div.)
V
OUT
CS5156
R1
10k
R2
6.2k
R3
10k
Power Good
5V
PN3904
PN3904
(R1 + R2)
×
0.65V
R2
Shutdown
Input
5V
V
FFB
CS5156
SS
5
8
IN4148
MMUN2111T1 (SOT-23)
相關PDF資料
PDF描述
CS5156GN16 CPU 5-Bit Nonsynchronous Buck Controller
CS5157GD16 CPU 5-Bit Synchronous Buck Controller
CS5157GDR16 CPU 5-Bit Synchronous Buck Controller
CS5157 CPU 5-Bit Synchronous Buck Controller
CS5157H CPU 5-Bit Synchronous Buck Controller
相關代理商/技術參數
參數描述
CS5156BT 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel
CS-5156D16 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller
CS5156GD16 制造商:Rochester Electronics LLC 功能描述:- Bulk
CS5156GN16 制造商:Rochester Electronics LLC 功能描述:- Bulk
CS-5156HD16 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller