- 您現在的位置：買賣IC網 > PDF目錄374167 > CS5150HGD16 (ZF Electronics Corporation) CPU 4-Bit Synchronous Buck Controller PDF資料下載
參數資料
| 型號： | CS5150HGD16 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | CPU 4-Bit Synchronous Buck Controller |
| 中文描述： | CPU的4位同步降壓控制器 |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 322K |
| 代理商： | CS5150HGD16 |
Applications Information: continued
C
10
Figure 14: Implementing shutdown with the CS5150H.
External Power Good Circuit
An optional Power Good signal can be generated through
the use of four additional external components (see Figure
15). The threshold voltage of the Power Good signal can be
adjusted per the following equation:
V
Power Good
=
This circuit provides an open collector output that drives
the Power Good output to ground for regulator voltages
less than V
Power Good
.
Figure 15: Implementing Power Good with the CS5150H.
Figure 16: CS5150H demonstration board during power up. Power Good
signal is activated when output voltage reaches 1.70V.
Selecting External Components
The CS5150H can be used with a wide range of external
power components to optimize the cost and performance of
a particular design. The following information can be used
as general guidelines to assist in their selection.
NFET Power Transistors
Both logic level and standard MOSFETs can be used. The
reference designs derive gate drive from the 12V supply
which is generally available in most computer systems and
utilize logic level MOSFETs. A charge pump may be easily
implemented to permit use of standard MOSFETs or sup-
port 5V or 12V only systems (maximum of 20V). Multiple
MOSFETs may be paralleled to reduce losses and improve
efficiency and thermal management.
Voltage applied to the MOSFET gates depends on the
application circuit used. Both upper and lower gate driver
outputs are specified to drive to within 1.5V of ground
when in the low state and to within 2V of their respective
bias supplies when in the high state. In practice, the MOS-
FET gates will be driven rail to rail due to overshoot caused
by the capacitive load they present to the controller IC. For
the typical application where V
CC1
= V
CC2
= 12V and 5V is
used as the source for the regulator output current, the fol-
lowing gate drive is provided;
V
GATE(H)
= 12V - 5V = 7V, V
GATE(L)
= 12V (see Figure 17).
Trace 3 = 12V Input (V
) and V
CC2
) (10V/div.)
Trace 4 = 5V Input (2V/div.)
Trace 1 = Regulator Output Voltage (1V/div.)
Trace 2 = Power Good Signal (2V/div.)
V
OUT
CS5150H
R1
10k
R2
6.2k
R3
10k
Power Good
5V
PN3904
PN3904
(R1 + R2)
×
0.65V
R2
Shutdown
Input
5V
V
FFB
CS5150H
SS
5
8
IN4148
MMUN2111T1 (SOT-23)
相關PDF資料 |
PDF描述 |
|---|---|
| CS5150HGDR16 | CPU 4-Bit Synchronous Buck Controller |
| CS5150GDR16 | CPU 4-Bit Synchronous Buck Controller |
| CS5150 | CPU 4-Bit Synchronous Buck Controller |
| CS5150H | CPU 4-Bit Synchronous Buck Controller |
| CS5150GD16 | CPU 4-Bit Synchronous Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS-5150N16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| CS-5151D16 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Mode SMPS Controller |
| CS5151GDR16 | 制造商:CHERRY 功能描述: |
| CS5151GN16 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CS-5151H | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CPU 4-Bit Nonsynchronous Buck Controller |
發(fā)布緊急采購，3分鐘左右您將得到回復。