- 您現在的位置：買賣IC網 > PDF目錄352821 > CS5126D8 Current-Mode SMPS Controller PDF資料下載
參數資料
| 型號： | CS5126D8 |
| 英文描述： | Current-Mode SMPS Controller |
| 中文描述： | 電流模式開關電源控制器 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 184K |
| 代理商： | CS5126D8 |
CS51220
http://onsemi.com
8
APPLICATIONS INFORMATION
THEORY OF OPERATION
Feed Forward Voltage Mode Control
Conventional voltage mode control uses a fixed ramp
signal for pulse width modulation, typically utilizing the
oscillator output as the ramp signal. Since the only feedback
signal comes from the output, this results in inferior line
regulation
and
audio
susceptibility.
A
significant
improvement in line regulation and line transient response
can be achieved using Feed Forward Voltage Mode Control,
implemented using the CS51220 controller.
The enhancement comes from generating the ramp signal
using a pull–up resistor from the FF pin to the line voltage
and a capacitor to ground. The slope of the ramp then
depends on the line voltage. At the start of each switch cycle,
the capacitor connected to the FF pin is charged through the
resistor connected to the input voltage. Meanwhile, the VO
pin goes high to turn on a power mosfet through an external
gate driver. When the rising FF pin exceeds the COMP input
pin, as driven through the regulation feedback loop, VO goes
low and turns off the external switch. Simultaneously, the FF
capacitor is quickly discharged and set for the next switching
cycle.
Overall, both input and output voltages control the
dynamics of the duty cycle. As illustrated in Figure 3, with
a fixed input voltage the output voltage is regulated solely
by the error amplifier. For example, an elevated output
voltage pulls down the COMP pin through an external error
amplifier. This in turn causes duty cycle to decrease. On the
another hand, if the input voltage varies, the slope of the FF
pin ramp reacts correspondingly and immediately. As an
example shown in Figure 4, when the input voltage goes up,
the slope of the ramp signal increases, which reduces duty
cycle and counteracts the change. For line variations, feed
forward control requires less response from the error
amplifier, which improves the transient speed and DC
regulation.
Figure 3. Pulse Width Modulated by the Output
Voltage with a Constant Input Voltage
VIN
COMP
FF
VOUT
CT
VO
Figure 4. Pulse Width Modulated by the Input Voltage
with a Constant Output Voltage
VIN
COMP
FF
VOUT
CT
VO
The feed forward feature can also be employed for
volt–second clamp, which limits the maximum product of
input voltage and switch on time. This clamp is used in
circuits, such as forward and flyback converters, to prevent
the transformer from saturating. Calculations used in the
design of the volt–second clamp are presented in the Design
Guidelines section on page 12.
相關PDF資料 |
PDF描述 |
|---|---|
| CS5126DR8 | Current-Mode SMPS Controller |
| CS-5127 | Dual Output Non-Synchronous Buck Controller with Sync Function and Secon |
| CS-5127DW16 | Current-Mode SMPS Controller |
| CS-5127DWR16 | Current-Mode SMPS Controller |
| CS51414ED8 | SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS5126-KL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cirrus Logic 功能描述: |
| CS5126-KLZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Cirrus Logic 功能描述: |
| CS5126-KP | 制造商:Rochester Electronics LLC 功能描述:2-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, - Bulk |
| CS5126XDR8 | 功能描述:IC REG CTRLR FLYBK ISO PWM 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| CS-5127 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual Output Non-Synchronous Buck Controller with Sync Function and Secon |
發布緊急采購，3分鐘左右您將得到回復。