- 您現在的位置：買賣IC網 > PDF目錄374164 > CS3361YDR14 (ZF Electronics Corporation) Alternator Voltage Regulator FET Driver PDF資料下載
參數資料
| 型號： | CS3361YDR14 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | Alternator Voltage Regulator FET Driver |
| 中文描述： | 發電機電壓調節器FET驅動器 |
| 文件頁數： | 4/5頁 |
| 文件大小： | 139K |
| 代理商： | CS3361YDR14 |
4
C
Application Information
The CS3361 is designed for use in an alternator charging
system.
In a standard alternator design (Figure 1), the rotor carries
the field winding. An alternator rotor usually has several N
and S poles. The magnetic field for the rotor is produced by
forcing current through a field or rotor winding. The Stator
windings are formed into a number of coils spaced around
a cylindrical core. The number of coils equals the number
of pairs of N and S poles on the rotor. The alternating cur-
rent in the Stator windings is rectified by the diodes and
applied to the regulator. By controlling the amount of field
current, the magnetic field strength is controlled and hence
the output voltage of the alternator.
Figure 1. IAR System Block Diagram
Referring to Figure 2, a typical application diagram, the
oscillator frequency is set by an external capacitor connect-
ed between OSC and ground. The sawtooth waveform
ramps between 1V and 3V and provides the timing for the
system. For the circuit shown the oscillator frequency is
approximately 140Hz. The alternator voltage is sensed at
Terminal A via the resistor divider network R1/R2 on the
Sense pin of the IC. The voltage at the sense pin determines
the duty cycle for the regulator. The voltage is adjusted by
potentiometer R2. A relatively low voltage on the sense pin
causes a long duty cycle that increases the Field current. A
high voltage results in a short duty cycle.
The ignition Terminal (I) switches power to the IC through
the V
CC
pin. The Stator pin monitors the voltage from the
stator and senses a stopped engine condition. It drives the
Lamp pin high after the stator timeout expires. The Lamp
pin also goes high when an overvoltage condition is detect-
ed on the sense pin. This causes the darlington lamp drive
transistor to switch on and pull current through the lamp.
If the system voltage continues to increase, the field and
lamp output turn off as in an overvoltage or load dump
condition.
The SC or Short Circuit pin monitors the field voltage. If
the drive output and the SC voltage are simultaneously
high for a predetermined period, a short circuit condition is
assumed and the output is disabled. The regulator is forced
to a minimum short circuit duty cycle.
BATTERY
Lamp
Indicator
ISWITCH
Regulator
I
Gnd
FIELD
A
S
FIELD Winding
Winding
Figure 2. Typical Application Diagram
R2
10k
SC
Driver
Gnd
STATOR
Sense
V
CC
OSC
IGN
20k
C4
0.022
μ
F
50k
C3
.047
μ
F
100k
250
C1
0.1
μ
F
18k
R4
BATTERY
LAMP
2.4k
10
Power
Darlington
ILamp
IGNITION
POWER
Logic level N
channel
FIELD
R5
R3
R1
R6
R9
R7
R10
STATOR
RECTIFIER
A
F
I
S
D1
Q1
*
C2
10
μ
F
*
Note: C2 optional for reduced jitter.
相關PDF資料 |
PDF描述 |
|---|---|
| CS3706 | IC AC/DC CONV 15V 300MA SIP12 |
| CS3706GNF16 | Dual Output Driver |
| CS3717AGNF16 | 1A H-Bridge Stepper Motor Driver |
| CS3717A | IC CONV AC/DC -12V 800MA SIP12 |
| CS3720XDPS7 | Xfmr Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS3361YDR14G | 功能描述:馬達/運動/點火控制器和驅動器 ANA IAR FET DRVR RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| CS33-64KJ1M93B | 制造商:Vishay Dale 功能描述:CS 33 64K 1M93 5% 0,1% E - Waffle Pack |
| CS33-676KBB | 制造商:Vishay Dale 功能描述:CS 33 676K 0,1% 0,1% E - Waffle Pack |
| CS337 | 功能描述:固態繼電器-PCB安裝 RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CS338 | 功能描述:固態繼電器-PCB安裝 RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。