- 您現在的位置：買賣IC網 > PDF目錄366892 > CR16MCT9VJE7Y Microcontroller PDF資料下載
參數資料
| 型號： | CR16MCT9VJE7Y |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 46/157頁 |
| 文件大?。?/td> | 1256K |
| 代理商： | CR16MCT9VJE7Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
46
When the counter reaches zero, an internal timer signal
called T0OUT is set to 1 for one T0IN clock cycle. This signal
sets the TC bit in the TWMT0 Control and Status Register
(T0CSR). It also generates an interrupt called RTI (IRQ14) if
the interrupt is enabled by the T0CSR.T0INTE bit.
If the software loads TWMT0 with a new value, the timer uses
that value the next time that it reloads the 16-bit timer register
(in other words, after reaching zero). The software can restart
the timer at any time (on the very next edge of the T0IN clock)
by setting the Restart (RST) bit in the T0CSR register. The
T0CSR.RST bit is cleared automatically upon restart of the
16-bit timer.
Note:
If the user wishes to switch to power save or idle mode
after setting T0CSR.RST, the user must wait for reset opera-
tion to complete before doing the switch.
14.3
The WATCHDOG is an 8-bit down counter that operates on
the rising edge of a specified clock source. Upon reset, the
WATCHDOG is disabled; it does not count and no WATCH-
DOG signal is generated. A write to either the WATCHDOG
Count (WDCNT) register or the WATCHDOG Service Data
Match (WDSDM) register starts the counter. The WATCH-
DOG counter counts down from the value programmed in to
the WDCNT register. Once started, only a reset can stop the
WATCHDOG from operating.
The WATCHDOG can be programmed to use either T0OUT
or T0IN as its clock source (the output and input of Timer T0,
respectively). The TWCFG.WDCT0I bit controls this clock se-
lection.
The software must periodically “service” the WATCHDOG.
There are two ways to service the WATCHDOG, the choice
depending on the programmed value of the WDSDME bit in
the Timer and WATCHDOG Configuration (TWCFG) register.
If TWCFG.WDSDME bit is cleared to 0, the WATCHDOG is
serviced by writing a value to the WDCNT register. The value
written to the register is reloaded into the WATCHDOG
counter. The counter then continues counting down from that
value.
If TWCFG.WDSDME bit is set to 1, the WATCHDOG is ser-
viced by writing the value 5C hex to the WATCHDOG Service
Data Match (WDSDM) register. This reloads the WATCH-
DOG counter with the value previously programmed into the
WDCNT register. The counter then continues counting down
from that value.
A WATCHDOG error signal is generated by any of the follow-
ing events:
— The WATCHDOG serviced too late.
— The WATCHDOG serviced too often.
— The WDSDM register is written with a value other than
5C hex when WDSDM type servicing is enabled
(TWCFG.WDSDME=1).
A WATCHDOG error condition resets the device.
WATCHDOG OPERATION
14.3.1
The Timer and WATCHDOG Configuration (TWCFG) regis-
ter is used to set the WATCHDOG configuration. It controls
the WATCHDOG clock source (T0IN or T0OUT), the type of
WATCHDOG servicing (using WDCNT or WDSDM), and the
Register Locking
locking state of the TWCFG, TWCPR, TIMER0, T0CSR, and
WDCNT registers. A register that is locked cannot be read or
written. A write operation is ignored and a read operation re-
turns unpredictable results.
If the TWCFG register is itself locked, it remains locked until
the device is reset. Any other locked registers also remain
locked until the device is reset. This feature prevents a run-
away program from tampering with the programmed
WATCHDOG function.
14.3.2
The Timer and WATCHDOG Module is active in both the
Power Save and Idle modes. The clocks and counters con-
tinue to operate normally in these modes. The WDSDM reg-
ister is accessible in the Power Save and Idle modes, but the
other TWM registers are accessible only in the Active mode.
Therefore, WATCHDOG servicing must be carried out using
the WDSDM register in the Power Save or Idle mode.
In the Halt mode, the entire device is frozen, including the
Timer and WATCHDOG Module. Upon return to the Active
mode, operation of the module resumes at the point at which
it was stopped.
Note:
After a restart or WATCHDOG service through WD-
CNT, do not enter Power Save mode for a period equivalent
to 5 slow clock cycles.
Power Save Mode Operation
14.4
The TWM registers controls the operation of the Timing and
WATCHDOG Module. There are six such registers:
— Timer and WATCHDOG Configuration Register
(TWCFG)
— Timer and WATCHDOG Clock Prescaler Register
(TWCP)
— TWM Timer 0 Register (TWMT0)
— TWMT0 Control and Status Register (T0CSR)
— WATCHDOG Count Register (WDCNT)
— WATCHDOG Service Data Match Register (WDSDM)
The WDSDM register is accessible in both Active and Power
Save mode. The other TWM registers are accessible only in
Active mode.
TWM REGISTERS
14.4.1
Timer and WATCHDOG Configuration Register
(TWCFG)
The TWCFG register is a byte-wide, read/write register that
selects the WATCHDOG clock input and service method, and
also allows the WATCHDOG registers to be selectively
locked. Once a bit is set, that bit cannot be cleared until the
device resets. Upon reset, the non-reserved bits of the regis-
ter are all cleared to 0. The register format is shown below.
LTWCFG
Lock TWCFG Register. When cleared to 0, ac-
cess to the TWCFG register is allowed. When
set to 1, the TWCFG register is locked. A
locked register cannot be read or written; a
read operation returns unpredictable values
and a write operation is ignored. Locking the
TWCFG register remains in effect until the de-
vice is reset.
7
6
5
4
3
2
1
0
Reserved WDSDME WDCT0I LWDCNT
LTWMT0 LTWCP LTWCFG
相關PDF資料 |
PDF描述 |
|---|---|
| CR16MCT9VJE8 | Microcontroller |
| CR16MCT9VJE8Y | Microcontroller |
| CR16MCT9VJE9 | Microcontroller |
| CR16MCT9VJE9Y | Microcontroller |
| CR18250 | Battery |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16MCT9VJE8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16MCT9VJE8Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16MCT9VJE9 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16MCT9VJE9Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16MCT9VJEX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:CR16MCT9/CR16MCT5/CR16HCT9/CR16HCT5 16-Bit Reprogrammable/ROM Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。