- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16MCS9VJE8Y Microcontroller PDF資料下載
參數資料
| 型號： | CR16MCS9VJE8Y |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 110/157頁 |
| 文件大小： | 1256K |
| 代理商： | CR16MCS9VJE8Y |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁當前第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
110
Setting the DDIR bit to “1” will cause the direction of the data
storage to be reversed — the last byte received is stored at
the highest address and the first byte is stored at the lowest
address. See Figure 70 for illustration.
LO
Listen Only — By setting the LO-bit to “1” the
CR16CAN interface is configured to behave
only as a receiver. This means:
it cannot transmit any message.
it cannot send a dominant ACK bit.
when errors are detected on the bus, the
CR16CAN will behave as in the error pas-
sive mode.
Using this listen only function, the CR16CAN
interface can be adjusted when it gets connect-
ed to an operating network with unknown bus
speed.
Ignore Acknowledge. If the ignore ACK func-
tion is enabled, then by setting the IGNACK bit
to “1”, CR16CAN does not expect to receive a
dominant ACK bit to indicate the validity of a
transmitted message. It will not send an error
frame when the transmitted frame in not ac-
knowledged by any other CAN node.
This feature can be used in conjunction with
the LOOPBACK option for stand-alone tests
outside of a CAN network.
LOOPBACK Loopback. By setting the LOOPBACK bit, all
messages sent by CR16CAN can also be re-
ceived by a CR16CAN buffer with a matching
buffer ID. However, CR16CAN does not ac-
knowledge a message sent by itself. Therefore
CR16CAN will send an error frame when no
other device connected to the bus has ac-
knowledged the message.
INTERNAL
Internal. If the INTERNAL function is enabled,
the TX- and RX-pin of the CR16CAN are inter-
nally connected to each other. This feature can
be used in conjunction with the LOOPBACK
mode. This means that CR16CAN can receive
its own sent messages without connecting an
external transceiver chip to the RX- and TX-
pin; it allows the user to run real stand-alone
tests without any peripheral devices.
IGNACK
DIAGEN
Diagnostic Enable. The DIAGEN bit globally
enables or disables the special diagnostic fea-
tures of CR16CAN. This includes the following
functions:
LO (Listen Only)
IGNACK (Ignore Acknowledge)
LOOPBACK (Loopback)
INTERNAL (Internal Loopback)
write access to hidden receive buffer
Error Interrupt Type. This bit configures when
the Error Interrupt Pending Bit (CIPND.EIPND)
is set and an error interrupt is generated if en-
abled
by
the
Error
(CIEN.EIEN).
“0”
The EIPND bit is set on every error on the
CAN bus.
“1”
The EIPND bit is set only if the error state
(CSTPND.NS) changes as a result of in-
crementing either the receive or transmit
error counter.
EIT
Interrupt
Enable
t
ADDRoffset
Data Bytes
Data1
Data2
Data3
Data4
Data5
Data6
Data7
Data8
Sequence of Data Bytes on the Bus
Storage of Data Bytes
in the Buffer Memory
Data1
Data3
Data2
Data4
Data5
Data6
Data7
Data8
ID
CRC
Figure 70.
Data Direction Bit set to ‘1’
0A
16
08
16
06
16
04
16
相關PDF資料 |
PDF描述 |
|---|---|
| CR16MCT5VJE7Y | Microcontroller |
| CR16HCS5VJE8 | Microcontroller |
| CR16HCS9VJE7Y | Microcontroller |
| CR16HCS9VJE8Y | Microcontroller |
| CR16HCT5 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16MCS9VJE9 | 功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| CR16MCS9VJE9/NOPB | 功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| CR16MCS9VJE90 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
| CR16MCS9VJE91 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
| CR16MCS9VJE92 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Family of 16-bit CAN-enabled CompactRISC Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。