- 您現在的位置：買賣IC網 > PDF目錄366882 > CPD-E200E Monitor_ICs:CXA2067S LM2415 CXD9516P H8D2957 uPC4558G2 TDA8177 uPC6757CS LA6500-FA LA6500-FA TEA1504/N2 BA00AST-V5 TLP621D4-Y-LF2T TL1431CZ-AP PQ12RD8S BA05T TA7805S CXA8070AP STK391-110 LA6510 CXD9528S CXA8071CP PST9143NL PDF資料下載
參數資料
| 型號： | CPD-E200E |
| 英文描述： | Monitor_ICs:CXA2067S LM2415 CXD9516P H8D2957 uPC4558G2 TDA8177 uPC6757CS LA6500-FA LA6500-FA TEA1504/N2 BA00AST-V5 TLP621D4-Y-LF2T TL1431CZ-AP PQ12RD8S BA05T TA7805S CXA8070AP STK391-110 LA6510 CXD9528S CXA8071CP PST9143NL |
| 中文描述： | Monitor_ICs：CXA2067S LM2415 CXD9516P H8D2957 uPC4558G2 TDA8177 uPC6757CS LA6500發LA6500發TEA1504/N2 BA00AST - V5的TLP621D4 - Y型LF2T TL1431CZ -美聯社PQ12RD8S BA05T TA7805S CXA8070AP STK391 - 110 LA6510 CXD9528S CXA8071CP PST9143NL |
| 文件頁數： | 10/46頁 |
| 文件大?。?/td> | 3051K |
| 代理商： | CPD-E200E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
1
14
Trouble symptoms and remedies
If the problem is caused by the connected computer or other equipment, please refer to the connected equipment’s instruction manual.
Use the self-diagnosis function (page 16) if the following recommendations do not resolve the problem.
Symptom
No picture
Check these items
If the
1
(power) indicator is not lit
Check that the power cord is properly connected.
Check that the
1
(power) switch is in the “on” position.
If the NO INPUT SIGNAL message
appears on the screen, or if the
1
(power) indicator is either orange or
alternating between green and
orange
Check that the video signal cable is properly connected and all plugs are firmly seated in
their sockets (page 6).
Check that the HD15 video input connector’s pins are not bent or pushed in.
x
Check that the computer’s power is “on.”
Check that the graphic board is completely seated in the proper bus slot.
x
The computer is in power saving mode. Try pressing any key on the computer keyboard.
Check that the computer’s power is “on.”
Check that the graphic board is completely seated in the proper bus slot.
If the MONITOR IS IN POWER
SAVE MODE message appeared on
the screen, or if the
1
(power)
indicator is either orange or
alternating between green and
orange
If the OUT OF SCAN RANGE
message appears on the screen
x
Check that the video frequency range is within that specified for the monitor. If you
replaced an old monitor with this monitor, reconnect the old monitor and adjust the
frequency range to the following.
Horizontal: 30 – 85 kHz
Vertical: 48 – 120 Hz
If no message is displayed and the
1
(power) indicator is green or flashing
orange
Use the Self-diagnosis function (page 16).
If using Windows 95/98
If you replaced an old monitor with this monitor, reconnect the old monitor and do the
following. Install the Windows Monitor Information Disk (page 7) and select this monitor
(“CPD-E200E”) from among the Sony monitors in the Windows 95/98 monitor selection
screen.
If using a Macintosh system
Check that the Macintosh adapter (not supplied) and the video signal cable are properly
connected (page 6).
Picture flickers, bounces,
Isolate and eliminate any potential sources of electric or magnetic fields such as other
monitors, laser printers, electric fans, fluorescent lighting, or televisions.
Move the monitor away from power lines or place a magnetic shield near the monitor.
Try plugging the monitor into a different AC outlet, preferably on a different circuit.
Try turning the monitor 90
°
to the left or right.
x
Check your graphics board manual for the proper monitor setting.
Confirm that the graphics mode (VESA, Macintosh 16" Color, etc.) and the frequency of
the input signal are supported by this monitor (Appendix). Even if the frequency is within
the proper range, some video boards may have a sync pulse that is too narrow for the
monitor to sync correctly.
Adjust the computer’s refresh rate (vertical frequency) to obtain the best possible picture.
Picture is fuzzy
Adjust the brightness and contrast (page 9).
Degauss the monitor* (page 11).
Select MOIRE ADJUST and adjust the moire cancellation effect (page 11).
15
GB
* If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard, but this is not a
malfunction.
Displaying this monitor’s name, serial number,
and date of manufacture.
While the monitor is receiving a video signal, press and hold the
center of the control button for more than five seconds to display
this monitor’s information box.
If the problem persists, call your authorized Sony dealer and give
the following information.
Model name: CPD-E200E
Serial number
Name and specifications of your computer and graphics board.
Picture is ghosting
Eliminate the use of video cable extensions and/or video switch boxes.
Check that all plugs are firmly seated in their sockets.
Picture is not centered or sized
Adjust the size (page 9) or centering (page 9). Note that some video modes do not fill the
screen to the edges.
Edges of the image are curved
Wavy or elliptical pattern (moire)
Adjust the geometry (page 10).
Select MOIRE ADJUST and adjust the moire cancellation effect (page 11).
x
Change your desktop pattern.
Color is not uniform
Degauss the monitor* (page 11). If you place equipment that generates a magnetic field,
such as a speaker, near the monitor, or if you change the direction the monitor faces, color
may lose uniformity.
White does not look white
Letters and lines show red or blue
Monitor buttons do not operate
A hum is heard right after the
Adjust the color temperature (page 10).
Adjust the convergence (page 10).
If the control lock is set to ON, set it to OFF (page 11).
This is the sound of the auto-degauss cycle. When the power is turned on, the monitor is
automatically degaussed for five seconds.
Symptom
Check these items
MENU
MODEL : CPD - E2 0 0E
MANUFACTURED : 1 9 9
I NFORMAT I ON
9 - 52
Example
b
相關PDF資料 |
PDF描述 |
|---|---|
| CPD200-4530 | 200 ? 250 Watt CompactPCI?DC-DC Converters |
| CPD200-4530G | 200 ? 250 Watt CompactPCI?DC-DC Converters |
| CPD250-4530G | 200 ? 250 Watt CompactPCI?DC-DC Converters |
| CPH3123 | BJT |
| CPH3217 | TRANSISTOR | BJT | NPN | 15V V(BR)CEO | 3A I(C) | SOT-346 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CPDER12V | 功能描述:ESD 抑制器 1 CH Bidirectional 12V DFN RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| CPDER12V0U | 功能描述:ESD 抑制器 1CH Unidirctionl ESD Suppressor 12V DFN RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| CPDER12V0U-HF | 功能描述:ESD 抑制器 Bidir, 12V RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| CPDER12V-HF | 功能描述:ESD 抑制器 Bidir, 12V RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
| CPDER24V | 功能描述:ESD 抑制器 1 CH Bidirectional 24V DFN RoHS:否 制造商:STMicroelectronics 通道:8 Channels 擊穿電壓:8 V 電容:45 pF 端接類型:SMD/SMT 封裝 / 箱體:uQFN-16 功率耗散 Pd: 工作溫度范圍:- 40 C to + 85 C |
發布緊急采購，3分鐘左右您將得到回復。