- 您現在的位置：買賣IC網 > PDF目錄9495 > CP82C54 (Intersil)IC OSC PROG TIMER 8MHZ 24DIP PDF資料下載
參數資料
| 型號： | CP82C54 |
| 廠商： | Intersil |
| 文件頁數： | 4/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OSC PROG TIMER 8MHZ 24DIP |
| 標準包裝： | 15 |
| 類型： | 可編程計時器 |
| 頻率： | 8MHz |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 10mA |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 24-DIP（0.600"，15.24mm） |
| 包裝： | 管件 |
| 供應商設備封裝： | 24-PDIP |
| 安裝類型： | 通孔 |
| 產品目錄頁面： | 1236 (CN2011-ZH PDF) |
12
82C54
If an initial count is written while GATE = 0, it will still be
loaded on the next CLK pulse. When GATE goes high, OUT
will go high N CLK pulses later; no CLK pulse is needed to
load the counter as this has already been done.
NOTES: The following conventions apply to all mode timing diagrams.
1. Counters are programmed for binary (not BCD) counting and for
reading/writing least significant byte (LSB) only.
2. The counter is always selected (CS always low).
3. CW stands for “Control Word”; CW = 10 means a control word of
10, Hex is written to the counter.
4. LSB stands for Least significant “byte” of count.
5. Numbers below diagrams are count values. The lower number is
the least significant byte. The upper number is the most
significant byte. Since the counter is programmed to read/write
LSB only, the most significant byte cannot be read.
6. N stands for an undefined count.
7. Vertical lines show transitions between count values.
MODE 1: HARDWARE RETRIGGERABLE ONE-SHOT
OUT will be initially high. OUT will go low on the CLK pulse
following a trigger to begin the one-shot pulse, and will remain
low until the Counter reaches zero. OUT will then go high and
remain high until the CLK pulse after the next trigger.
After writing the Control Word and initial count, the Counter is
armed. A trigger results in loading the Counter and setting
OUT low on the next CLK pulse, thus starting the one-shot
pulse N CLK cycles in duration. The one-shot is retriggerable,
hence OUT will remain low for N CLK pulses after any trigger.
The one-shot pulse can be repeated without rewriting the
same count into the counter. GATE has no effect on OUT.
If a new count is written to the Counter during a one-shot
pulse, the current one-shot is not affected unless the
Counter is retriggerable. In that case, the Counter is loaded
with the new count and the one-shot pulse continues until
the new count expires.
CW = 10
LSB = 4
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
CW = 10
LSB = 3
CW = 10
LSB = 3
LSB = 2
NNN
N
0
4
0
3
0
2
0
1
0
FF
FE
NNNN
0
3
0
2
0
2
0
2
0
1
0
FF
NNNN
0
3
0
2
0
1
0
2
0
1
0
FF
FIGURE 9. MODE 0
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
NN
0
3
0
2
0
1
0
FF
0
3
0
2
N
CW = 12
LSB = 3
CW = 12
LSB = 3
CW = 12
LSB = 2
LSB = 4
N
NNN
0
2
0
1
0
FF
FE
0
4
0
3
N
NNNN
0
3
0
2
0
1
0
3
0
2
0
1
0
N
FIGURE 10. MODE 1
相關PDF資料 |
PDF描述 |
|---|---|
| CS3102A-24-62P | CONN RCPT 24POS BOX MNT W/PINS |
| CP82C54-10Z | IC OSC PROG TIMER 10MHZ 24PDIP |
| D38999/20MJ90SA | CONN RCPT 46POS WALL MNT W/SCKT |
| MS27473T24A61SB | CONN PLUG 61POS STRAIGHT W/SCKT |
| D38999/24WJ20PB | CONN RCPT 30POS JAM NUT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP82C5410 | 制造商:Harris Corporation 功能描述: |
| CP82C54-10 | 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 10MHZ 24PDIP COM RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| CP82C54-10Z | 功能描述:計時器和支持產品 W/ANNEAL PERIPH PRG- CNTR 5V 10MHZ 24PDIP RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| CP82C54-10Z | 制造商:Intersil Corporation 功能描述:CMOS PROGRAMMABLE INT TIMER SMD 制造商:Intersil Corporation 功能描述:CMOS, PROGRAMMABLE INT TIMER, SMD |
| CP82C54-10Z | 制造商:Intersil Corporation 功能描述:Microprocessor Support IC Package/Case:2 |
發布緊急采購，3分鐘左右您將得到回復。