- 您現在的位置：買賣IC網 > PDF目錄9452 > CP82C54-12 (Intersil)IC OSC PROG TIMER 12MHZ 24DIP PDF資料下載
參數資料
| 型號： | CP82C54-12 |
| 廠商： | Intersil |
| 文件頁數： | 3/22頁 |
| 文件大小： | 0K |
| 描述： | IC OSC PROG TIMER 12MHZ 24DIP |
| 標準包裝： | 165 |
| 類型： | 可編程計時器 |
| 頻率： | 12MHz |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 10mA |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 24-DIP（0.600"，15.24mm） |
| 包裝： | 管件 |
| 供應商設備封裝： | 24-PDIP |
| 安裝類型： | 通孔 |
11
82C54
MODE DEFINITIONS
The following are defined for use in describing the operation
of the 82C54.
CLK PULSE -
A rising edge, then a falling edge, in that
order, of a Counter’s CLK input.
TRIGGER -
A rising edge of a Counter’s Gate input.
COUNTER LOADING -
The transfer of a count from the CR
to the CE (See “Functional Description”)
MODE 0: INTERRUPT ON TERMINAL COUNT
Mode 0 is typically used for event counting. After the Control
Word is written, OUT is initially low, and will remain low until
the Counter reaches zero. OUT then goes high and remains
high until a new count or a new Mode 0 Control Word is
written to the Counter.
GATE = 1 enables counting; GATE = 0 disables counting.
GATE has no effect on OUT.
After the Control Word and initial count are written to a
Counter, the initial count will be loaded on the next CLK
pulse. This CLK pulse does not decrement the count, so for
an initial count of N, OUT does not go high until N + 1 CLK
pulses after the initial count is written.
If a new count is written to the Counter it will be loaded on
the next CLK pulse and counting will continue from the new
count. If a two-byte count is written, the following happens:
1. Writing the first byte disables counting. Out is set low
immediately (no clock pulse required).
2. Writing the second byte allows the new count to be
loaded on the next CLK pulse.
This allows the counting sequence to be synchronized by
software. Again OUT does not go high until N + 1 CLK
pulses after the new count of N is written.
COMMANDS
DESCRIPTION
RESULT
D7
D6
D5
D4
D3
D2
D1
D0
1
0
1
0
Read-Back Count and Status of Counter 0
Count and Status Latched for Counter 0
1
0
1
0
Read-Back Status of Counter 1
Status Latched for Counter 1
1
0
1
0
Read-Back Status of Counters 2, 1
Status Latched for Counter 2,
But Not Counter 1
1
0
1
0
Read-Back Count of Counter 2
Count Latched for Counter 2
1
0
1
0
Read-Back Count and Status of Counter 1
Count Latched for Counter 1,
But Not Status
1
0
1
0
Read-Back Status of Counter 1
Command Ignored, Status Already
Latched for Counter 1
FIGURE 7. READ-BACK COMMAND EXAMPLE
CS
RD
WR
A1
A0
01000
Write into Counter 0
01001
Write into Counter 1
01010
Write into Counter 2
01011
Write Control Word
00100
Read from Counter 0
00101
Read from Counter 1
00110
Read from Counter 2
00111
No-Operation (Three-State)
1
XXXX
No-Operation (Three-State)
0
1
X
No-Operation (Three-State)
FIGURE 8. READ/WRITE OPERATIONS SUMMARY
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B7M-MX-B1 | CONVERTER MOD DC/DC 10V 75W |
| IS82C54-10Z96 | IC OSC PROG TIMER 10MHZ 28PLCC |
| VE-B13-IU-F3 | CONVERTER MOD DC/DC 24V 200W |
| VE-B7L-MX-B1 | CONVERTER MOD DC/DC 28V 75W |
| NBVSPA015LNHTAG | IC VCXO LVDS 200MHZ 6CLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP82C54-12S2580 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C54-12Z | 功能描述:計時器和支持產品 W/ANNEAL PERIPH PRG- CNTR 5V 5MHZ 24PDIP RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| CP82C54R2489 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C54Z | 功能描述:計時器和支持產品 W/ANNEAL PERIPH PRG- CNTR 5V 8MHZ 24PDIP RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| CP82C55A | 功能描述:外圍驅動器與原件 - PCI PERIPH PRG-I/O 5V 8M HZ 40PDIP COM RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。