- 您現在的位置：買賣IC網 > PDF目錄9495 > CP82C54-10Z (Intersil)IC OSC PROG TIMER 10MHZ 24PDIP PDF資料下載
參數資料
| 型號： | CP82C54-10Z |
| 廠商： | Intersil |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OSC PROG TIMER 10MHZ 24PDIP |
| 標準包裝： | 15 |
| 類型： | 可編程計時器 |
| 頻率： | 10MHz |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 10mA |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 24-DIP（0.600"，15.24mm） |
| 包裝： | 管件 |
| 供應商設備封裝： | 24-PDIP |
| 安裝類型： | 通孔 |
| 產品目錄頁面： | 1236 (CN2011-ZH PDF) |
14
82C54
Mode 3 Is Implemented As Follows
EVEN COUNTS -
OUT is initially high. The initial count is
loaded on one CLK pulse and then is decremented by two
on succeeding CLK pulses. When the count expires, OUT
changes value and the Counter is reloaded with the initial
count. The above process is repeated indefinitely.
ODD COUNTS -
OUT is initially high. The initial count is loaded
on one CLK pulse, decremented by one on the next CLK pulse,
and then decremented by two on succeeding CLK pulses.
When the count expires, OUT goes low and the Counter is
reloaded with the initial count. The count is decremented by
three on the next CLK pulse, and then by two on succeeding
CLK pulses. When the count expires, OUT goes high again and
the Counter is reloaded with the initial count. The above
process is repeated indefinitely. So for odd counts, OUT will be
high for (N + 1)/2 counts and low for (N - 1)/2 counts.
MODE 4: SOFTWARE TRIGGERED MODE
OUT will be initially high. When the initial count expires, OUT
will go low for one CLK pulse then go high again. The
counting sequence is “Triggered” by writing the initial count.
GATE = 1 enables counting; GATE = 0 disables counting.
GATE has no effect on OUT.
After writing a Control Word and initial count, the Counter will
be loaded on the next CLK pulse. This CLK pulse does not
decrement the count, so for an initial count of N, OUT does not
strobe low until N + 1 CLK pulses after the initial count is
written.
If a new count is written during counting, it will be loaded on
the next CLK pulse and counting will continue from the new
count. If a two-byte count is written, the following happens:
1. Writing the first byte has no effect on counting.
2. Writing the second byte allows the new count to be
loaded on the next CLK pulse.
This allows the sequence to be “retriggered” by software. OUT
strobes low N + 1 CLK pulses after the new count of N is
written.
MODE 5: HARDWARE TRIGGERED STROBE
(RETRIGGERABLE)
OUT will initially be high. Counting is triggered by a rising
edge of GATE. When the initial count has expired, OUT will
go low for one CLK pulse and then go high again.
After writing the Control Word and initial count, the counter
will not be loaded until the CLK pulse after a trigger. This
CLK pulse does not decrement the count, so for an initial
count of N, OUT does not strobe low until N + 1 CLK pulses
after trigger.
A trigger results in the Counter being loaded with the initial
count on the next CLK pulse. The counting sequence is
triggerable. OUT will not strobe low for N + 1 CLK pulses
after any trigger GATE has no effect on OUT.
If a new count is written during counting, the current counting
sequence will not be affected. If a trigger occurs after the
new count is written but before the current count expires, the
NNN
N
0
2
0
1
0
FF
FE
FF
FD
0
3
WR
CLK
GATE
OUT
CW = 18
LSB = 3
WR
CLK
GATE
OUT
WR
CLK
GATE
OUT
CW = 18
LSB = 3
CW = 18
LSB = 3
NN
N
0
3
0
2
0
1
0
2
0
1
0
FF
NN
N
0
3
0
3
0
2
0
1
0
FF
0
3
LSB = 2
N
FIGURE 13. MODE 4
相關PDF資料 |
PDF描述 |
|---|---|
| D38999/20MJ90SA | CONN RCPT 46POS WALL MNT W/SCKT |
| MS27473T24A61SB | CONN PLUG 61POS STRAIGHT W/SCKT |
| D38999/24WJ20PB | CONN RCPT 30POS JAM NUT W/PINS |
| MS27467E13B4S | CONN PLUG 4POS STRAIGHT W/SCKT |
| D38999/20MJ90SN | CONN RCPT 46POS WALL MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP82C54-10Z | 制造商:Intersil Corporation 功能描述:CMOS PROGRAMMABLE INT TIMER SMD 制造商:Intersil Corporation 功能描述:CMOS, PROGRAMMABLE INT TIMER, SMD |
| CP82C54-10Z | 制造商:Intersil Corporation 功能描述:Microprocessor Support IC Package/Case:2 |
| CP82C54-12 | 功能描述:計時器和支持產品 PERIPH PRG-CNTR 5V 12 5MHZ 24PDIP COM RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| CP82C54-12S2580 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CP82C54-12Z | 功能描述:計時器和支持產品 W/ANNEAL PERIPH PRG- CNTR 5V 5MHZ 24PDIP RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。