- 您現在的位置：買賣IC網 > PDF目錄26505 > CP2102-GMR (SILICON LABORATORIES) PDF資料下載
參數資料
| 型號： | CP2102-GMR |
| 廠商： | SILICON LABORATORIES |
| 元件分類： | 總線控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, QCC28 |
| 封裝： | 5 X 5 MM, LEAD FREE, QFN-28 |
| 文件頁數： | 3/18頁 |
| 文件大小： | 373K |
| 代理商： | CP2102-GMR |
CP2102
Rev. 1.1
11
5. USB Function Controller and Transceiver
The Universal Serial Bus function controller in the CP2102 is a USB 2.0 compliant full-speed device with integrated
transceiver and on-chip matching and pull-up resistors. The USB function controller manages all data transfers
between the USB and the UART as well as command requests generated by the USB host controller and
commands for controlling the function of the UART.
The USB Suspend and Resume signals are supported for power management of both the CP2102 device as well
as external circuitry. The CP2102 will enter Suspend mode when Suspend signaling is detected on the bus. On
entering Suspend mode, the CP2102 asserts the SUSPEND and SUSPEND signals. SUSPEND and SUSPEND
are also asserted after a CP2102 reset until device configuration during USB Enumeration is complete.
The CP2102 exits the Suspend mode when any of the following occur: (1) Resume signaling is detected or
generated, (2) a USB Reset signal is detected, or (3) a device reset occurs. On exit of Suspend mode, the
SUSPEND and SUSPEND signals are de-asserted.
Both SUSPEND and SUSPEND temporarily float high during a CP2102 reset. If this behavior is undesirable, a
strong pulldown (10 k
) can be used to ensure SUSPEND remains low during reset. See Figure 6 for other
recommended options.
Figure 6. Typical Connection Diagram
Option 1: A 4.7 k
pull-up resistor can be added to increase noise immunity.
Option 2: A 4.7 F tantalum capacitor can be added if powering other devices from the on-chip regulator.
Option 3: Avalanche transient voltage suppression diodes should be added for ESD protection.
Option 3: Use Littlefuse p/n SP0503BAHT or equivalent.
Option 4: 10 k
resistor to ground to hold SUSPEND low on initial power on or device reset.
1
CP2102
SUSPEND
11
12
REGIN
7
GND
3
RST
9
D+
4
D-
5
8
C2
0.1
F
C1
1
F
RI
DCD
CTS
RTS
RXD
TXD
DSR
DTR
2
1
28
27
26
25
24
23
2
3
External RS-232
transceiver or
UART circuitry
(to external circuitry
for USB suspend
states)
VBUS
D-
D+
GND 4
5
6
USB
CONNECTOR
6
VDD
VBUS
VDD
R1
4.7 k
D1
D2
D3
Option 1
R2
10 k
Option 4
Option 3
C4
4.7
F
TANT
Option 2
相關PDF資料 |
PDF描述 |
|---|---|
| CP2103-GMR | |
| CP2104-F03-GM | |
| CP2105-F01-GM | |
| CP2110-F01-GM | |
| CPC1009NTR | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CP210-2N4416-CT | 功能描述:JFET N-Channel 30V 5mA @ 20V Surface Mount Die 制造商:central semiconductor corp 系列:- 包裝:托盤 零件狀態:有效 FET 類型:N 溝道 電壓 - 擊穿（V（BR）GSS）:30V 漏源極電壓（Vdss）:30V 不同 Vds（Vgs=0）時的電流 - 漏極（Idss）:5mA @ 20V 漏極電流（Id） - 最大值:- 不同 Id 時的電壓 - 截止（VGS 關）:6V @ 1nA 不同 Vds 時的輸入電容（Ciss）:4pF @ 15V 電阻 - RDS（開）:- 安裝類型:表面貼裝 封裝/外殼:模具 供應商器件封裝:模具 功率 - 最大值:- 標準包裝:1 |
| CP210-2N4416-CT20 | 功能描述:JFET N-Channel 30V 5mA @ 20V Surface Mount Die 制造商:central semiconductor corp 系列:- 包裝:托盤 零件狀態:有效 FET 類型:N 溝道 電壓 - 擊穿（V（BR）GSS）:30V 漏源極電壓（Vdss）:30V 不同 Vds（Vgs=0）時的電流 - 漏極（Idss）:5mA @ 20V 漏極電流（Id） - 最大值:- 不同 Id 時的電壓 - 截止（VGS 關）:6V @ 1nA 不同 Vds 時的輸入電容（Ciss）:4pF @ 15V 電阻 - RDS（開）:- 安裝類型:表面貼裝 封裝/外殼:模具 供應商器件封裝:模具 功率 - 最大值:- 標準包裝:1 |
| CP2102N-A01-GQFN20 | 功能描述:USB TO UART BRIDGE - QFN20 制造商:silicon labs 系列:* 零件狀態:有效 標準包裝:100 |
| CP2102N-A01-GQFN20R | 功能描述:USB Bridge, USB to UART USB 2.0 UART Interface 制造商:silicon labs 標準包裝:1,500 |
| CP2102N-A01-GQFN24 | 功能描述:USB TO UART BRIDGE - QFN24 制造商:silicon labs 系列:* 零件狀態:有效 標準包裝:100 |
發布緊急采購，3分鐘左右您將得到回復。