- 您現在的位置：買賣IC網 > PDF目錄379935 > COP8SDR9HVA7 (NATIONAL SEMICONDUCTOR CORP) 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout PDF資料下載
參數資料
| 型號： | COP8SDR9HVA7 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| 中文描述： | 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQCC44 |
| 封裝： | PLASTIC, LCC-44 |
| 文件頁數： | 23/80頁 |
| 文件大?。?/td> | 972K |
| 代理商： | COP8SDR9HVA7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
10.0 Functional Description
(Continued)
In Case 1, V
rises from 0V and the on-chip RESET is
undefined until the supply is greater than approximately
1.0V. At this time the brownout circuit becomes active and
holds the device in RESET. As the supply passes a level of
about 1.8V, a delay of about 3 ms (t
) is started and the Idle
Timer is preset to a value between 00F0 and 00FF (hex).
Once V
is greater than V
and t
d
has expired, the Idle
Timer is allowed to count down (t
id
).
Case 2 shows a subsequent dip in the supply voltage which
goes below the approximate 1.8V level. As V
CC
drops below
V
bor
, the internal RESET signal is asserted. When V
CC
rises
back above the 1.8V level, t
d
is started. Since the power
supply rise time is longer for this case, t
d
has expired before
V
CC
rises above V
bor
and t
id
starts immediately when V
CC
is
greater than V
bor
.
Case 3 shows a dip in the supply where V
drops below
V
bor
, but not below 1.8V. On-chip RESET is asserted when
V
goes below V
bor
and t
id
starts as soon as the supply
goes back above V
bor
.
If the Brownout Reset feature is enabled, the internal reset
will not be turned off until the Idle Timer underflows. The
internal reset will perform the same functions as external
reset. The device is guaranteed to operate at the specified
frequency down to the specified brownout voltage. After the
underflow, the logic is designed such that no additional
internal resets occur as long as V
CC
remains above the
brownout voltage.
The device is relatively immune to short duration negative-
going V
transients (glitches). It is essential that good
filtering of V
be done to ensure that the brownout feature
works correctly. Power supply decoupling is vital even in
battery powered systems.
There are two optional brownout voltages. The part numbers
for the three versions of this device are:
COP8SBR9, V
bor
= low voltage range
COP8SCR9, V
bor
= high voltage range
COP8SDR9, BOR is disabled.
Refer to the device specifications for the actual V
bor
volt-
ages.
High brownout voltage devices are guaranteed to operate at
10MHz down to the brownout voltage. Low brownout voltage
devices are guaranteed to operate at 3.33MHz down to the
brownout voltage.
Devices are not guaranteed to operate
at 10MHz down to the low brownout voltage.
Under no circumstances should the RESET pin be allowed
to float. If the on-chip Brownout Reset feature is being used,
the RESET pin should be connected directly to V
CC
. The
RESET input may also be connected to an external pull-up
resistor or to other external circuitry. Any rising edge on the
RESET pin while V
is below the specified operating range
may cause unpredictable results. The output of the brownout
reset detector will always preset the Idle Timer to a value
between 00F0 and 00FF (240 to 256 t
C
). At this time, the
internal reset will be generated.
If the BOR feature is disabled, then no internal resets are
generated and the Idle Timer will power-up with an unknown
value. In this case, the external RESET must be used. When
BOR is disabled, this on-chip circuitry is disabled and draws
no DC current.
The contents of data registers and RAM are unknown fol-
lowing the on-chip reset.
10138913
FIGURE 10. Brownout Reset Operation
C
www.national.com
23
相關PDF資料 |
PDF描述 |
|---|---|
| COP8SBR9HVA8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SCR9HVA8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SDR9HVA8 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
| COP8SBR9 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout(8位基于CMOS 閃速存儲器的帶32K存儲器，虛擬EEPROM和電壓過低復位的微控制器) |
| COP8SCR9 | 8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout(8位基于CMOS 閃速存儲器的帶32K存儲器，虛擬EEPROM和電壓過低復位的微控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8SDR9HVA8 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8SDR9HVA8 63SN | 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 3.3V/5V 44-Pin PLCC Rail |
| COP8SDR9HVA8/63SN | 功能描述:閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| COP8SDR9HVA8/NOPB | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8SDR9IMT7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Based Microcontroller with 32k Memory, Virtual EEPROM and Brownout |
發布緊急采購，3分鐘左右您將得到回復。