參數資料
型號： COP8SAA716N9
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 微控制器/微處理器
英文描述： 8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging
中文描述： 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PDIP16
封裝： DIP-16
文件頁數： 33/60頁
文件大小： 787K
代理商： COP8SAA716N9
9.0 Interrupts
(Continued)
9.4 NON-MASKABLE INTERRUPT
9.4.1 Pending Flag
There is a pending flag bit associated with the non-maskable
interrupt,
called
STPND.
memory-mapped and cannot be accessed directly by the
software.
The pending flag is reset to zero when a device Reset oc-
curs. When the non-maskable interrupt occurs, the associ-
ated pending bit is set to 1. The interrupt service routine
should contain an RPND instruction to reset the pending flag
to zero. The RPND instruction always resets the STPND
flag.
This
pending
flag
is
not
9.4.2 Software Trap
The Software Trap is a special kind of non-maskable inter-
rupt which occurs when the INTR instruction (used to ac-
knowledge interrupts) is fetched from program memory and
placed in the instruction register. This can happen in a vari-
ety of ways, usually because of an error condition. Some ex-
amples of causes are listed below.
If the program counter incorrectly points to a memory loca-
tion beyond the available program memory space, the
non-existent or unused memory location returns zeroes
which is interpreted as the INTR instruction.
If the stack is popped beyond the allowed limit (address 02F
or 06F Hex), a Software Trap is triggered.
A Software Trap can be triggered by a temporary hardware
condition such as a brownout or power supply glitch.
The Software Trap has the highest priority of all interrupts.
When a Software Trap occurs, the STPND bit is set. The GIE
bit is not affected and the pending bit (not accessible by the
user) is used to inhibit other interrupts and to direct the pro-
gram to the ST service routine with the VIS instruction. Noth-
ing can interrupt a Software Trap service routine except for
another Software Trap. The STPND can be reset only by the
RPND instruction or a chip Reset.
The Software Trap indicates an unusual or unknown error
condition. Generally, returning to normal execution at the
point where the Software Trap occurred cannot be done re-
liably. Therefore, the Software Trap service routine should
reinitialize the stack pointer and perform a recovery proce-
dure that restarts the software at some known point, similar
to a device Reset, but not necessarily performing all the
same functions as a device Reset. The routine must also ex-
ecute the RPND instruction to reset the STPND flag. Other-
wise, all other interrupts will be locked out. To the extent pos-
sible, the interrupt routine should record or indicate the
context of the device so that the cause of the Software Trap
can be determined.
If the user wishes to return to normal execution from the
point at which the Software Trap was triggered, the user
must first execute RPND, followed by RETSK rather than
RETI or RET. This is because the return address stored on
the stack is the address of the INTR instruction that triggered
the interrupt. The program must skip that instruction in order
to proceed with the next one. Otherwise, an infinite loop of
Software Traps and returns will occur.
Programming a return to normal execution requires careful
consideration. If the Software Trap routine is interrupted by
another Software Trap, the RPND instruction in the service
routine for the second Software Trap will reset the STPND
flag; upon return to the first Software Trap routine, the
STPND flag will have the wrong state. This will allow
maskable interrupts to be acknowledged during the servicing
of the first Software Trap. To avoid problems such as this, the
user program should contain the Software Trap routine to
perform a recovery procedure rather than a return to normal
execution.
Under normal conditions, the STPND flag is reset by a
RPND instruction in the Software Trap service routine. If a
programming error or hardware condition (brownout, power
supply glitch, etc.) sets the STPND flag without providing a
way for it to be cleared, all other interrupts will be locked out.
To alleviate this condition, the user can use extra RPND in-
structions in the main program and in the WATCHDOG ser-
vice routine (if present). There is no harm in executing extra
RPND instructions in these parts of the program.
9.5 PORT L INTERRUPTS
Port L provides the user with an additional eight fully select-
able, edge sensitive interrupts which are all vectored into the
same service subroutine.
The interrupt from Port L shares logic with the wake up cir-
cuitry. The register WKEN allows interrupts from Port L to be
individually enabled or disabled. The register WKEDG speci-
fies the trigger condition to be either a positive or a negative
edge. Finally, the register WKPND latches in the pending
trigger conditions.
The GIE (Global Interrupt Enable) bit enables the interrupt
function.
A control flag, LPEN, functions as a global interrupt enable
for Port L interrupts. Setting the LPEN flag will enable inter-
rupts and vice versa. A separate global pending flag is not
needed since the register WKPND is adequate.
Since Port L is also used for waking the device out of the
HALT or IDLE modes, the user can elect to exit the HALT or
IDLE modes either with or without the interrupt enabled. If he
elects to disable the interrupt, then the device will restart ex-
ecution from the instruction immediately following the in-
struction that placed the microcontroller in the HALT or IDLE
modes. In the other case, the device will first execute the in-
terrupt service routine and then revert to normal operation.
(See HALT MODE for clock option wakeup information.)
9.6 INTERRUPT SUMMARY
The device uses the following types of interrupts, listed be-
low in order of priority:
1.
The Software Trap non-maskable interrupt, triggered by
the INTR (00 opcode) instruction. The Software Trap is
acknowledged immediately. This interrupt service rou-
tine can be interrupted only by another Software Trap.
The Software Trap should end with two RPND instruc-
tions followed by a restart procedure.
2.
Maskable interrupts, triggered by an on-chip peripheral
block or an external device connected to the device. Un-
der ordinary conditions, a maskable interrupt will not in-
terrupt any other interrupt routine in progress. A
maskable interrupt routine in progress can be inter-
rupted by the non-maskable interrupt request. A
maskable interrupt routine should end with an RETI in-
struction.
www.national.com
33
相關PDF資料
PDF描述
COP8SAA720M8 8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging
COP8SAA720M9 8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging
COP8SAA720N8 8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging
COP8SAA720N9 8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging
COP8SAA728M8 8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging
相關代理商/技術參數
參數描述
COP8SAA720M7 功能描述:IC MCU OTP 8BIT 1K POR 20-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8SA 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
COP8SAA720M8 功能描述:IC MCU OTP 8BIT 1K POR 20-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8SA 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
COP8SAA720M9 功能描述:IC MCU OTP 8BIT 1K 20SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8SA 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
COP8SAA720N8 功能描述:IC MCU OTP 8BIT 1K 20DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8SA 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
COP8SAA720N9 功能描述:IC MCU OTP 8BIT 1K 20DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8SA 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*