參數資料
型號： CMX228
英文描述： ISDN Protocol Engine? D-Channel Data??
中文描述： 綜合業務數字網協議引擎？ D信道數據？？
文件頁數： 18/38頁
文件大?。?/td> 361K
代理商： CMX228
ISDN Data and Telephony Protocol Engine (inc. X.25)
CMX228
1999
Consumer Microcircuits Limited
1999
Chiron Technology Limited
18
D/228/1
The escape sequence ‘+++’ (with Guard Time = 1s before and after the sequence) will cause the
CMX228 to enter the command state from the data state and to return an ‘OK’ response. Sending an
ATO command will be ignored, ie the CMX228 remains in the command state.
The following is a more detailed description of the Hayes commands listed above:
A (Answer)
Format:ATA<CR>
Causes the CMX228 to answer an incoming data call, by sending a CONNECT message to the
network. If a CONNECT ACK is received the CMX228 enters the data state after returning a
‘CONNECT XXX’ result code to the DTE on the RS232 port (where the XXX is the speed in baud). If
a RELEASE, RELEASE COMPLETE or DISCONNECT message is received a ‘NO CARRIER’ result
code is returned. The command is not valid if there is no incoming call and it will return ‘ERROR’.
D (Dial)
Format:ATD{DN}<CR>
Format:ATDT{DN}<CR>
Format:ATDP{DN}<CR>
{DN} is a directory number of up to 23 ASCII characters from 0..9,
S
and
#
. This form of the ATD
command causes an outgoing SETUP message to be sent to the network with a Called Party Number
Information Element which contains the digits included in the command. Any commands that follow
this command are ignored.
If the CMX228 receives any character from the DTE after an ATD command, which causes a SETUP
message to be sent to the network, and before the call is connected, the attempt to make a call is
abandoned, ie a DISCONNECT message will be sent to the network and a ‘NO CARRIER’ result code
returned.
Calls are established with the D command, irrespective of the state of the DTR pin. The result code
response is either:
'CONNECT'
'NO CARRIER'
'NO DIALTONE'
'BUSY'
- call successful. The CMX228 will automatically enter the data state.
- call rejected by the remote user or the network
- ISDN link down
- remote user busy and other causes
Calls are cleared in the following way:
(i) The remote end or network clears the call by sending a DISCONNECT message or the ISDN
line fails/is removed: 'NO CARRIER' is sent to DTE.
(ii) DTR is dropped (with a de-bounce period of 50ms) by DTE causing the CMX228 to send a
DISCONNECT message to the network and enter the disconnect state, awaiting a RELEASE
COMPLETE from the network. The CMX228 sends the 'OK' response when clearing of the ISDN
call is complete ie RELEASE and RELEASE COMPLETE messages have been transmitted
across the network, (dependant upon the state of &D command).
(iii) The DTE issues the escape sequence ‘+++ ‘(with Guard Time = 1s before and after the
sequence), receives an 'OK' response and then issues the Hang-up command (see section on H
command below). The CMX228 sends the 'OK' response when clearing of the ISDN call is
complete.
相關PDF資料
PDF描述
CMXT2207 BJT
CN305 Optoelectronic
CN3801 Analog IC
CN3802 Analog IC
CN3803 Analog IC
相關代理商/技術參數
參數描述
CMX228S1 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:ISDN Protocol Engine with D - channel Data
CMX264 制造商:CMLMICRO 制造商全稱:CML Microcircuits 功能描述:Frequency Domain Split Band Scrambler
CMX309 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CLOCK OSCILLATORS
CMX-309 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMX-309
CMX-309FAB 22.5792MB 功能描述:OSCILLATOR 22.5792MHZ 3.3V SMT RoHS:否 類別:晶體和振蕩器 >> 振蕩器 系列:CMX-309 標準包裝:1 系列:VG-4512CA 類型:VCXO 頻率:153.6MHz 功能:三態（輸出啟用） 輸出:LVPECL 電源電壓:3.3V 頻率穩定性:- 工作溫度:-40°C ~ 85°C 電流 - 電源（最大）:60mA 額定值:- 安裝類型:表面貼裝 尺寸/尺寸:0.276" L x 0.197" W（7.00mm x 5.00mm） 高度:0.071"（1.80mm） 封裝/外殼:6-SMD，無引線（DFN，LCC） 包裝:Digi-Reel® 電流 - 電源（禁用）（最大）:- 其它名稱:SER3790DKR
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*