- 您現在的位置：買賣IC網 > PDF目錄379899 > CLM2815AU-X (CALOGIC LLC) 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output Fast Response PDF資料下載
參數資料
| 型號： | CLM2815AU-X |
| 廠商： | CALOGIC LLC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1.5A Low Dropout Voltage Regulator Adjustable & Fixed Output Fast Response |
| 中文描述： | 1.5A的低壓差線性穩壓器可調節 |
| 文件頁數： | 3/6頁 |
| 文件大小： | 84K |
| 代理商： | CLM2815AU-X |
APPLICATION HINTS
The Calogic Semiconductor CLM2815 incorporates protection
against over-current faults, reversed load insertion, over
temperature operation, and positive and negative transient
voltage. However, the use of an output capacitor is required
in order to insure the stability and the performances.
Stability
The output capacitor is part of the regulator’s frequency
compensation system. Either a 220
μ
F aluminum electrolytic
capacitor or a 47
μ
F solid tantalum capacitor between the
output terminal and ground guarantees stable operation for all
operating conditions.
However, in order to minimize overshoot and undershoot, and
therefore optimize the design, please refer to the section
’Ripple Rejection’.
Ripple Rejection
Ripple rejection can be improved by adding a capacitor
between the ADJ pin and ground. When ADJ pin bypassing is
used, the value of the output capacitor required increases to
its maximum (220
μ
F for an aluminum electrolytic capacitor, or
47
μ
F for a solid tantalum capacitor). If the ADJ pin is not
bypass, the value of the output capacitor can be lowered to
100
μ
F for an electrolytic aluminum capacitor or 15
μ
F for a
solid tantalum capacitor.
However the value of the ADJ-bypass capacitor should be
chosen with respect to the following equation:
C = 1 / ( 6.28
F
R
R
1
)
Where C = value of the capacitor in Farads (select an equal or
larger standard value),
F
R
= ripple frequency in Hz,
R
1
= value of resistor R
1
in Ohms.
If an ADJ-bypass capacitor is used, the amplitude of the
output ripple will be independent of the output voltage. If an
ADJ-bypass capacitor is not used, the output ripple will be
proportional to the ratio of the output voltage to the reference
voltage:
M = V
OUT
/ V
REF
Where M = multiplier for the ripple seen when the ADJ pin is
optimally bypassed.
V
REF
= Reference Voltage
Reducing parasitic resistance and inductance
One solution to minimize parasitic resistance and inductance
is to connect in parallel capacitors. This arrangement will
improve the transient response of the power supply if your
system requires rapidly changing current load condition.
Thermal Consideration
Although the CLM2815 offers some limiting circuitry for
overload conditions, it is necessary not to exceed the
maximum junction temperature, and therefore to be careful
about thermal resistance. The heat flow will follow the lowest
resistance path, which is the Junction-to-case thermal
resistance. In order to insure the best thermal flow of the
component, a proper mounting is required. Note that the case
of the device is electrically connected to the output. In case
the case has to be electrically isolated, a thermally conductive
spacer can be used. However do not forget to consider its
contribution to thermal resistance.
Assuming:
V
IN
= 10V, V
OUT
= 5V, I
OUT
= 1.5A, T
A
= 90
o
C,
Θ
CASE
= 1
o
C/W
(no external heat sink, no wind)
Power dissipation under these conditions
P
D
= (V
IN
- V
OUT
)
I
OUT
= 7.5W
Junction Temperature
T
J
= T
A
+ P
D
(
Θ
CASE
+
Θ
JC
)
For the Control Section
T
J
= 90
o
C + 7.5W
(1
o
C/W + 0.6
o
C/W) = 102
o
C
114
o
C T
JUNCTION MAX
for the control section.
For the Power Section
T
J
= 90
o
C + 7.5W
(1
o
C/W + 1.6
o
C/W) = 104.5
o
C
109.5
o
C T
JUNCTION MAX
for the power transistor.
In both cases reliable operation is insured by adequate
junction temperature.
CALOGIC CORPORATION
, 237 Whitney Place, Fremont, California 94539, Telephone: 510-656-2900, FAX: 510-651-3025
CLM2815
CORPORATION
相關PDF資料 |
PDF描述 |
|---|---|
| CLM2830AT | 3.0A Low Dropout Voltage Regulator Adjustable |
| CLM2830AU | 3.0A Low Dropout Voltage Regulator Adjustable |
| CLM2830 | 3.0A Low Dropout Voltage Regulator Adjustable |
| CLM285-12 | Micropower Voltage Reference Diode |
| CLM385-12 | Micropower Voltage Reference Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CLM281FAR | 制造商:RAY 功能描述:RAYTHEON L-BAND |
| CLM28-1-FAR | 制造商:RAY 功能描述:RAYTHEON L-BAND |
| CLM2830 | 制造商:CALOGIC 制造商全稱:CALOGIC 功能描述:3.0A Low Dropout Voltage Regulator Adjustable |
| CLM2830AT | 制造商:CALOGIC 制造商全稱:CALOGIC 功能描述:3.0A Low Dropout Voltage Regulator Adjustable |
| CLM2830AU | 制造商:CALOGIC 制造商全稱:CALOGIC 功能描述:3.0A Low Dropout Voltage Regulator Adjustable |
發布緊急采購，3分鐘左右您將得到回復。