- 您現在的位置：買賣IC網 > PDF目錄379896 > CLC428A8B (COMLINEAR CORP) Dual Wideband, Low-Noise, Voltage Feedback Op Amp PDF資料下載
參數資料
| 型號： | CLC428A8B |
| 廠商： | COMLINEAR CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Dual Wideband, Low-Noise, Voltage Feedback Op Amp |
| 中文描述： | DUAL OP-AMP, 2000 uV OFFSET-MAX, 135 MHz BAND WIDTH, CDIP8 |
| 封裝： | CERDIP-8 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 898K |
| 代理商： | CLC428A8B |
Figure 6
Positive Peak Detector
The CLC428's dual amplifiers can be used to implement a
unity-gain peak detector circuit as shown in Figure 7.
Figure 7
The acquisition speed of this circuit is limited by the
dynamic resistance of the diode when charging C
hold
. A
plot of the of the circuit's performance is shown in Figure
8 with a 1MHz sinusoidal input.
Figure 8
A current source, built around Q
1
, provides the necessary
bias current for the second amplifier and prevents satura-
tion when power is applied. The resistor, R, closes the loop
while diode D
2
prevents negative saturation when V
in
is
less than V
c
. A MOS-type switch (not shown) can be used
to reset the capacitor's voltage.
The maximum speed of detection is limited by the delay
of the op amps and the diodes. The use of Schottky diodes
will provide faster response.
Adjustable or Bandpass Equalizer
A "boost" equalizer can be made with the CLC428 by
summing a bandpass response with the input signal, as
shown in Figure 9.
Figure 9
The overall transfer function is shown in Eq. 5.
V
V
R
K R
R
s2Q
ω
s
sQ
1
out
in
b
+
a
b
o
+
2
o
o
2
=
F
I
+
h
ω
ω
Eq. 5
To build a boost circuit, use the design equations Eq. 6 and
Eq. 7.
R C
2
Q, 2C R ||R
o
ω
1
ω
Q
a
b
o
=
=
h
Eq. 6,7
Select R
2
and C using Eq. 6. Use reasonable values for
high frequency circuits - R
2
between 10
and 5k
, C
between 10pF and 2000pF. Use Eq. 7 to determine the
parallel combination of R
a
and R
b
. Select R
a
and R
b
by
either the 10
to 5k
criteria or by other requirements
based on the impedance V
in
is capable of driving. Finish
the design by determining the value of K from Eq. 8.
Peak Gain
V
V
R
KR
2
out
in
o
a
=
=
ω
c h
2
1
Eq. 8
Figure 10 shows an example of the response of the circuit
of Figure 9, where f
is 2.3MHz. The component values
are as follows: R
a
=2.1k
, R
b
=68.5
, R
2
=4.22k
, R
=500
, KR =50
, C =120pF.
Figure 10
Q
1
http://www.national.com
6
相關PDF資料 |
PDF描述 |
|---|---|
| CLC428 | Dual Wideband, Low-Noise, Voltage Feedback Op Amp |
| CLC428AJE | Dual Wideband, Low-Noise, Voltage Feedback Op Amp |
| CLC430 | General Purpose 100MHz Op Amp with Disable |
| CLC431 | Dual Wideband Monolithic Op Amp with Disable |
| CLC432 | Dual Wideband Monolithic Op Amp with Disable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CLC428AIB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
| CLC428AJE | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:OC White Company 功能描述:OP Amp Dual Volt Fdbk ±5V/12V 8-Pin SOIC N |
| CLC428AJE-TR13 | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| CLC428AJP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| CLC428SMD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier |
發(fā)布緊急采購，3分鐘左右您將得到回復。