- 您現在的位置：買賣IC網 > PDF目錄384194 > CH1793 MODEM PDF資料下載
參數資料
| 型號： | CH1793 |
| 英文描述： | MODEM |
| 中文描述： | 調制解調器 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 1942K |
| 代理商： | CH1793 |
2000 Cermetek Microelectronics, Inc.
Page 13
Document No. 607-0003 Revision G (05/00)
In addition to restriction notification, the FCC requires that
Cermetek make all repairs to all products in the HS Modem
family. If repairs are necessary after installation of the HS
Modem and the end product has been delivered to the end
user, the end product must be returned to the end product
supplier where the HS Modem can be removed and then
forwarded to Cermetek repair. The following notice is
recommended and should be included in the end product’s
user manual.
FOR YOUR USER’S MANUAL
The part 68 rules require the following (or equivalent) be
provided to the end user of the equipment containing a
DAA:
Type of Service:
The (insert end product name) is
designed to be used on standard device telephone lines. It
connects to the telephone line by means of a standard jack
called the USOC RJ-11C (or USOC RJ45S). Connection to
telephone-company-provided coin service (central office
implemented systems) is prohibited. Connection to party
lines service is subject to state tariffs.
Changes in Attestation Procedure for Plugs and Jacks:
(Name of applicant) attests that the network interface plugs
or jacks used on this equipment comply with and will
continue to comply with the mechanical requirements
specified in Part 68, Sub-part F, specifically the
dimensions, tolerances and metallic plating requirements.
The compliance of these connectors will be assured by
purchase
specifications
and
Documentation of such specifications and/or inspections
will be provided by the FCC within 30 days of their request
for the same.
incoming
inspection.
Telephone Company Procedure:
The goal of the
telephone company is to provide you with the best service
it can. In order to do this, it may occasionally be necessary
for them to make changes in their equipment, operations or
procedures. If these changes might effect your service or
the operation of your equipment, the telephone company
will give you notice, in writing, to allow you to make any
changes necessary to maintain uninterrupted service.
In certain circumstances, it may be necessary for the
telephone company to request information from you
concerning the equipment which you have connected to
your telephone line. Upon request of the telephone
company, provide the FCC registration number and the
ringer equivalence number (REN); both of these items are
listed on the equipment label. The sum of all of the REN’s
on your telephone lines should be less than five in order to
assure proper service from the telephone company. In
some cases, a sum of five may not be useable on a given
line. Consult your telephone provider.
If Problems Arise:
If any of your telephone equipment is
not operating properly, you should immediately remove it
from your telephone line, as it may cause harm to the
telephone network. If the telephone company notes a
problem, they may temporarily discontinue service. When
practical, they will notify you in advance of this
disconnection. If advance notice is not feasible, you will be
notified as soon as possible.
When you are notified, you will be given the opportunity to
correct the problem and informed of your right to a file a
complaint with the FCC. Contact your local telephone
service provider if you have any questions about your phone
line.
In the event repairs are ever needed on the (insert your
product name), they should be performed by (insert your
company name) or an authorized representative of (insert
your company name). For information contact: (insert your
company address).
DEFAULT STATUS, PERFORMANCE AND SPECS
Prior to delivery , Cermetek installs into each HS Modem the
following the Default Configuration Profile:
Default Connect Speeds are 14,400bps, 28,800bps, 33,600bps and
56,000bps for CH1794, CH1798, CH1799 and CH2056 respectively
Serial port data rate auto baud enabled
Bell 212A operation at 1200bps
Parity - none
Auto answer disabled
Command echo ON
All result codes enabled – except \REL codes
Wait for dial tone before dialing – 2 seconds
Dials with touch-tone (T)
Detects busy signal (ATX4)
Full word result codes - non-extended
Pulse dial make/break ratio = 39/61- 10 pps
Test timer set to 0 seconds, test modes disabled
Inactivity timer set to 0 minutes
CTS always active
DSR is ignored
DCD is ignored
RTS to CTS delay - .01 seconds
DTR always active - hangs up after transition
Long space disconnect disabled
Speaker enabled but off when receiving carrier
Speaker volume set to low
Local modem will not grant RDL request from remote modem
Guard tones disabled
Minimum DTR pulse width = .05 seconds
Ring count – 00
Escape code character = 43 (+)
Flash to on hook = 70 ms
Auto speed detection enabled
DTE connect speed, connect messages
Back space character = 08 (BS)Carriage return character = 13 (CR)
Line feed character = 10 (LF)
Duration of wait for dial tone = 2 seconds
Duration of wait for carrier after dialing = 50 seconds
Carrier detect response time = 0.6 seconds
Escape code guard time = 1 second
Length of use after comma = 2.0 seconds
Last carrier to hang up delay = 1.4 seconds
DTMF interdigit delay = .095 seconds
Auto sync address or address detection = 0
Connection detected at DTE – Highest speed 38,400bps
Auto retrain enabled - 30 seconds attempt
MNP error correction mode can be negotiated (&Q5)
MNP - non-extended service selected
MNP error correction block size is 128 characters selected
Data compression -negotiation enabled
Transmit break length is 0.3 seconds
All breaks are transmitted in sequence with data
Serial port flow control enabled = RTS/CTS
XON/XOFF flow control characters selected
NOTE: Upon power-up the HS Modem will recall user profile 0
which may override some of the above Factory Defaults. If
desired the user may, at their option, save the factory defaults
in user profile 0.
相關PDF資料 |
PDF描述 |
|---|---|
| CH1793ET | Telecommunication IC |
| CH1793LT | Telecommunication IC |
| CH1798 | Telecommunication IC |
| CH1798ET | MODEM |
| CH1799ET | MODEM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CH1793ET | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| CH1793LT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| CH1794 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HIGH SPEED Modem and FAX FAMILY |
| CH1794A | 制造商:Cermetek Microelectronics 功能描述:Modem Chip Single 57.6Kbps 22-Pin |
| CH1794A ET | 制造商:Cermetek Microelectronics 功能描述:Extended Temp. CH1794A, -40 oC - +85oC |
發布緊急采購，3分鐘左右您將得到回復。