參數資料
型號： CDALA10M7GA067
廠商： Murata Manufacturing Co., Ltd.
英文描述： Ceramic Filters (CERAFIL) for FM Receivers
中文描述： 陶瓷濾波器（濾波器陶瓷濾波器）的調頻接收器
文件頁數： 11/57頁
文件大小： 992K
代理商： CDALA10M7GA067
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested
to approve our product specification or to transact the approval sheet for product specification, before your ordering.
P61E7.pdf 01.10.17
Chip CERAFIL
r
SFECS Series Notice
10
2
I
Notice (Soldering and Mounting)
1. Standard Reflow Soldering Condition
(1) Reflow
The component cannot be withstand washing.
2. Wash
Filter shall be soldered at 280
±
5C for 3.0
±
0.5 seconds.
The soldering iron shall not touch the filter white soldering.
(2) Soldering Iron
T
100
200
240
30 sec.
min.
30 sec.
max.
Peak
(240C max.)
Pre-heating
(120-170C)
Heating
(200C)
Gradual
Cooling
120 sec.
min.
60-120 sec.
I
Notice (Handling)
1. The component will be damaged when an excessive
stress is applied.
2. The component may be damaged if excess mechanical
stress is applied to it mounted on the printed circuit
board.
3. Design layout of components on the PC board to
minimize the stress imposed on the warp or flexure of the
board.
4. After installing chips, if solder is excessively applied to
the circuit board, mechanical stress will cause destruction
resistance characteristics to lower. To prevent this, be
extremly careful in determining shape and dimension
before designing the circuit board diagram.
5. When the positioning claws and pick up nozzle are worn,
the load is applied to the chip while positioning is
concentrated to one positioning accuracy, etc. Careful
checking and maintenance are necessary to prevent
unexpected trouble.
6. When correcting chips with a soldering iron, the tip of the
soldering iron should not directly touch the chip
component. Depending on the soldering conditions, the
effective area of terminations may be reduced. The use
of solder containing Ag should be done to prevent the
electrode erosion.
7. Do not clean or wash the component as it is not
hermetically sealed.
8. In case of covering filter with over coat, conditions such
as material of resin, cure temperature, and so on should
be evaluated well.
9. Do not use strong acidity flux, more than 0.2wt% chlorine
content, in re-flow soldering.
10. Accurate test circuit values are required to measure
electrical characteristics.
It may be a cause of mis-correlation if there is any
deviation, especially stray capacitance, from the test
circuit in the specification.
[Component layout close to board]
Susceptibility to
stress is in the order
of : A>C>B
B
A
C
Slit
Perforation
相關PDF資料
PDF描述
CDALA10M7GA068 Ceramic Filters (CERAFIL) for FM Receivers
CDALA10M7GA069 Ceramic Filters (CERAFIL) for FM Receivers
CDALA10M7GA070 Ceramic Filters (CERAFIL) for FM Receivers
CDALA10M7GA071 RES 1.6K-OHM 2% 1.0W 100PPM MET-FILM AXIAL TR-13 R-MIL-PRF-39017
CDALA10M7GA073 Ceramic Filters (CERAFIL) for FM Receivers
相關代理商/技術參數
參數描述
CDALA10M7GA068 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Ceramic Filters (CERAFIL) for FM Receivers
CDALA10M7GA069 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Ceramic Filters (CERAFIL) for FM Receivers
CDALA10M7GA070 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Ceramic Filters (CERAFIL) for FM Receivers
CDALA10M7GA071 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Ceramic Filters (CERAFIL) for FM Receivers
CDALA10M7GA073 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:Ceramic Filters (CERAFIL) for FM Receivers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*