- 您現在的位置：買賣IC網 > PDF目錄379732 > CBC2016T (Analog Devices, Inc.) Dual 600mA Step-Down Converter with Synchronization PDF資料下載
參數資料
| 型號： | CBC2016T |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Dual 600mA Step-Down Converter with Synchronization |
| 中文描述： | 雙600mA降壓轉換器的同步 |
| 文件頁數： | 13/22頁 |
| 文件大?。?/td> | 719K |
| 代理商： | CBC2016T |
This equation also makes the worst-case assump-
tion that both converters are operating at 50% duty
cycle synchronized.
· 1
-
IN
V
IN
The term
voltage ripple and input capacitor RMS current
equations. It is at maximum when V
O
is twice V
IN
.
This is why the input voltage ripple and the input
capacitor RMS current ripple are a maximum at
50% duty cycle.
appears in both the input
The input capacitor provides a low impedance loop
for the edges of pulsed current drawn by the
AAT2513. Low ESR/ESL X7R and X5R ceramic
capacitors are ideal for this function. To minimize
the stray inductance, the capacitor should be
placed as close as possible to the IC. This keeps
the high frequency content of the input current
localized, minimizing EMI and input voltage ripple.
The proper placement of the input capacitor (C3 and
C9) can be seen in the evaluation board layout in
Figures 3 and 4. Since decoupling must be as close
to the input pins as possible it is necessary to use
two decoupling capacitors, one for each converter.
A Laboratory test set-up typically consists of two
long wires running from the bench power supply to
the evaluation board input voltage pins. The induc-
tance of these wires along with the low ESR ceram-
ic input capacitor can create a high Q network that
may effect the converter performance.
This problem often becomes apparent in the form
of excessive ringing in the output voltage during
load transients. Errors in the loop phase and gain
measurements can also result.
Since the inductance of a short printed circuit board
trace feeding the input voltage is significantly lower
than the power leads from the bench power supply,
most applications do not exhibit this problem.
In applications where the input power source lead
inductance cannot be reduced to a level that does
not effect the converter performance, a high ESR
tantalum or aluminum electrolytic (C10 of Figure 2)
should be placed in parallel with the low ESR, ESL
bypass ceramic. This dampens the high Q network
and stabilizes the system.
Output Capacitor
The output capacitor limits the output ripple and
provides holdup during large load transitions. A
4.7μF to 10μF X5R or X7R ceramic capacitor typi-
cally provides sufficient bulk capacitance to stabi-
lize the output during large load transitions and has
the ESR and ESL characteristics necessary for low
output ripple.
The output voltage droop due to a load transient is
dominated by the capacitance of the ceramic out-
put capacitor. During a step increase in load cur-
rent the ceramic output capacitor alone supplies
the load current until the loop responds. As the loop
responds the inductor current increases to match
the load current demand. This typically takes two
to three switching cycles and can be estimated by:
Once the average inductor current increases to the
DC load level, the output voltage recovers. The
above equation establishes a limit on the minimum
value for the output capacitor with respect to load
transients.
The internal voltage loop compensation also limits
the minimum output capacitor value to 4.7μF. This
is due to its effect on the loop crossover frequency
(bandwidth), phase margin, and gain margin.
Increased output capacitance will reduce the
crossover frequency with greater phase margin.
The maximum output capacitor RMS ripple current
is given by:
Dissipation due to the RMS current in the ceramic
output capacitor ESR is typically minimal, resulting in
less than a few degrees rise in hot spot temperature.
O
V
O
1
2
3
V
OUT
· (V
IN(MAX)
- V
OUT
)
L
·
F
·
V
IN(MAX)
RMS(MAX)
I
=
·
·
C
OUT
=
3
·
Δ
I
LOAD
V
DROOP
·
F
S
· 1
-
= D
(1 - D) = 0.5
2
= 0.25
V
IN
V
IN
V
O
AAT2513
Dual 600mA Step-Down
Converter with Synchronization
2513.2007.04.1.1
13
相關PDF資料 |
PDF描述 |
|---|---|
| CBC2518T | Dual 600mA Step-Down Converter with Synchronization |
| CBM103B | MODEM Transformer |
| CBM103 | MODEM Transformer |
| CBM1180 | Fastest & Securest USB 2.0/USB1.1 Flash Disk Controller with dedicated 32-bit microprocessor |
| CBM1183 | Fastest & Securest USB 2.0/USB1.1 Flash Disk Controller with dedicated 32-bit microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CBC2016T100 | 制造商:TAIYO-YUDEN 制造商全稱:Taiyo Yuden (U.S.A.), Inc 功能描述:WOUND CHIP INDUCTORS |
| CBC2016T100K | 功能描述:固定電感器 INDCTR HI CUR WND 0806 10uH 10% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| CBC2016T100KR | 制造商:TAIYO-YUDEN 制造商全稱:Taiyo Yuden (U.S.A.), Inc 功能描述:WIRE-WOUND CHIP POWER INDUCTORS (CB SERIES) |
| CBC2016T100M | 功能描述:固定電感器 INDCTR HI CUR WND 0806 10uH 20% RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
| CBC2016T100M-K | 功能描述:固定電感器 10uH 20% Wound Chip RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm |
發布緊急采購，3分鐘左右您將得到回復。