Figure 2. I2C Serial Interface" />
參數資料
型號: CAT9554AWI-GT2
廠商: ON Semiconductor
文件頁數: 10/14頁
文件大?。?/td> 0K
描述: IC I/O EXPANDER I2C 8B 16SOIC
標準包裝: 1
接口: I²C,SM 總線
輸入/輸出數: 8
中斷輸出:
頻率 - 時鐘: 400kHz
電源電壓: 2.3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 16-SOIC
包裝: 標準包裝
包括: POR
其它名稱: CAT9554AWI-GT2DKR
CAT9554, CAT9554A
http://onsemi.com
5
SCL
SDA IN
SDA OUT
Figure 2. I2C Serial Interface Timing
tSU:STA
tAA
tF
tHD:STA
tHD:DAT
tLOW
tDH
tR
tSU:DAT
tLOW
tHIGH
tSU:STO
tBUF
Pin Description
SCL: Serial Clock
The serial clock input clocks all data transferred into or out
of the device. The SCL line requires a pullup resistor if it
is driven by an open drain output.
SDA: Serial Data/Address
The bidirectional serial data/address pin is used to transfer
all data into and out of the device. The SDA pin is an open
drain output and can be wireORed with other open drain or
open collector outputs. A pullup resistor must be connected
from SDA line to VCC. The value of the pullup resistor, RP,
can be calculated based on minimum and maximum values
from Figure 3 and Figure 4 (see Note).
A0, A1, A2: Device Address Inputs
These inputs are used for extended addressing capability.
The A0, A1, A2 pins should be hardwired to VCC or VSS.
When hardwired, up to eight CAT9554/9554As may be
addressed on a single bus system. The levels on these inputs
are compared with corresponding bits, A2, A1, A0, from the
slave address byte.
I/O0 to I/O7: Input / Output Ports
Any of these pins may be configured as input or output.
The simplified schematic of I/O0 to I/O7 is shown in
Figure 5. When an I/O is configured as an input, the Q1 and
Q2 output transistors are off creating a high impedance input
with a weak pullup resistor (typical 100 k
W). If the I/O pin
is configured as an output, the pushpull output stage is
enabled. Care should be taken if an external voltage is
applied to an I/O pin configured as an output due to the low
impedance paths that exist between the pin and either VCC
or VSS.
Figure 3. Minimum RP Value vs.
Supply Voltage
Figure 4. Maximum RP Value vs.
Bus Capacitance
VCC (V)
CBUS (pF)
4.8
4.4
4.0
3.6
3.2
2.8
2.4
2.0
0
0.5
1.0
1.5
2.0
2.5
400
350
300
200
150
100
50
0
1
2
3
4
6
7
8
R
Pmin
(K
W
)
R
Pmax
(K
W
)
5.2
5.6
IOL = 3 mA @ VOLmax
250
5
Fast Mode I2C Bus /
tr max 300 ns
NOTE: According to the Fast Mode I2C bus specification, for bus capacitance up to 200 pF, the pull up device can be a resistor. For bus
loads between 200 pF and 400 pF, the pullup device can be a current source (Imax = 3 mA) or a switched resistor circuit.
相關PDF資料
PDF描述
CQ82C55A IC I/O EXPANDER 24B 44MQFP
ATMEGA88PV-10MUR MCU AVR 8KB FLASH 10MHZ 32QFN
PCA9535EMTTXG 16-BIT I/O EXPANDER
JLC1562BFEL IC BUS INTRFACE I2C I/O 16SOEIAJ
ATMEGA8515-16JUR MCU AVR 8KB FLASH 16MHZ 44PLCC
相關代理商/技術參數
參數描述
CAT9554AYGI 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT9554AYGI-T2 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT9554AYI-G 功能描述:接口-I/O擴展器 8-Bit Parallel IO RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel
CAT9554AYI-GT2 功能描述:接口 - 專用 I2C/SMBUS Expander 8B,w/Int RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
CAT9554HV4 制造商:Catalyst Semiconductor 功能描述: