- 您現在的位置：買賣IC網 > PDF目錄366731 > CAT3643HL1-T2 3-Channel Ultra High Efficiency Quad-Mode TM LED Driver PDF資料下載
參數資料
| 型號： | CAT3643HL1-T2 |
| 英文描述： | 3-Channel Ultra High Efficiency Quad-Mode TM LED Driver |
| 中文描述： | 3通道超高效率的Quad - Mode商標LED驅動器 |
| 文件頁數： | 12/17頁 |
| 文件大?。?/td> | 321K |
| 代理商： | CAT3643HL1-T2 |
CAT3643
Doc. No. 5022 Rev. B
12
2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
Unused LED Channels
For applications not requiring all the channels, it is
recommended the unused LED pins be tied directly to
V
OUT
(see Figure 4).
Figure 4. Application with 2 LEDs
Protection Mode
If an LED is disconnected, the driver senses that and
automatically ignores that channel. When all LEDs are
disconnected, the driver goes to 1x mode where the
output is equal to the input voltage.
As soon as the output exceeds about 6V, the driver
resets itself and reevaluate the mode.
If the die temperature exceeds +150°C, the driver will
enter a thermal protection shutdown mode. When the
device temperature drops by about 20°C, the device
will resume normal operation.
LED Selection
LEDs with forward voltages (V
F
) ranging from 1.3V to
4.3V may be used. Selecting LEDs with lower V
F
is
recommended in order to improve the efficiency by
keeping the driver in 1x mode longer as the battery
voltage decreases.
For example, if a white LED with a V
F
of 3.3V is
selected over one with V
F
of 3.5V, the driver will stay
in 1x mode for lower supply voltage of 0.2V. This
helps improve the efficiency and extends battery life.
External Components
The driver requires four external 1
μ
F ceramic capaci–
tors for decoupling input, output, and for the charge
pump. Both capacitors type X5R and X7R are
recommended for the LED driver application. In all
charge pump modes, the input current ripple is kept
very low by design and an input bypass capacitor of
1
μ
F is sufficient.
In 1x mode, the device operates in linear mode and
does not introduce switching noise back onto the
supply.
Recommended Layout
In charge pump mode, the driver switches internally at
a high frequency. It is recommended to minimize trace
length to all four capacitors. A ground plane should
cover the area under the driver IC as well as the
bypass capacitors. Short connection to ground on
capacitors C
IN
and C
OUT
can be implemented with the
use of multiple via. A copper area matching the TQFN
exposed pad (TAB) must be connected to the ground
plane underneath. The use of multiple via improves
the package heat dissipation.
Figure 5. TDFN-12 Recommended Layout
C2
C1
VIN
C
IN
C
OUT
GND
GND
VOUT
RSET
EN/DIM
Pin1
GND
V
IN
LED1
LED2
LED3
RSET
EN/DIM
CAT3643
V
IN
V
OUT
1μF
1μF
C
IN
C1-
C1+
C2-
C2+
1μF
1μF
C
OUT
R
SET
ENABLE
DIMMING
相關PDF資料 |
PDF描述 |
|---|---|
| CAT3643HV2-T2 | 3-Channel Ultra High Efficiency Quad-Mode TM LED Driver |
| CAT3643HV3-T2 | 3-Channel Ultra High Efficiency Quad-Mode TM LED Driver |
| CAT3644 | 4-Channel Ultra High Efficiency Quad-Mode TM LED Driver |
| CAT3644HV3-T2 | 4-Channel Ultra High Efficiency Quad-Mode TM LED Driver |
| CAT4016 | 16-Channel Constant Current LED Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT3643HV2-GT2 | 功能描述:LED照明驅動器 LED Driver,Quad mode,3 ch RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT3643HV2-T2 | 功能描述:LED照明驅動器 LED Driver,Quad mode,3 ch RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT3643HV3 | 制造商:ON Semiconductor 功能描述:IC 3-LED DRIVER QUAD HI EFFICIENCY |
| CAT3643HV3-GT2 | 功能描述:LED照明驅動器 LED Driver,Quad mode,3 ch RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT3643HV3-T2 | 功能描述:LED照明驅動器 3-Channel Quad-Mode RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。