- 您現在的位置：買賣IC網 > PDF目錄369654 > CAT34RC02YITE13 The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each PDF資料下載
參數資料
| 型號： | CAT34RC02YITE13 |
| 元件分類： | EEPROM |
| 英文描述： | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 中文描述： | 該CAT24FC02是一個2 KB的EEPROM的國內256個8位每字舉辦的串行CMOS |
| 文件頁數： | 5/14頁 |
| 文件大?。?/td> | 674K |
| 代理商： | CAT34RC02YITE13 |
DsconinuedPat
CAT34RC02
5
Doc No. 1052, Rev. O
2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
I
2
C BUS PROTOCOL
The I
2
C bus consists of two
‘
wires
’
, SCL and SDA. The
two
‘
wires
’
are connected to the supply (V
CC
) via pull-up
resistors. Master and Slave devices connect to the bus
via their respective SCL and SDA pins. The transmitting
device pulls down the SDA line to
‘
transmit
’
a
‘
0
’
and
releases it to
‘
transmit
’
a
‘
1
’
.
not busy (see A.C. Characteristics).
(2) During a data transfer, the data line must remain
stable whenever the SCL line is high. An SDA
transition while SCL is high will be interpreted as a
START or STOP condition.
START Condition
The START Condition precedes all commands. It consists
of a HIGH to LOW transition on SDA while SCL is HIGH.
The START condition acts as a
‘
wake-up
’
call for the
Slave devices. A Slave will not respond to commands
unless the MASTER generates a START condition.
STOP Condition
The STOP condition completes all commands. It consists
of a LOW to HIGH transition on SDA while SCL is HIGH.
The STOP condition starts the internal write cycle, when
following a WRITE command and sends the Slave into
standby mode, when following a READ command.
Device Addressing
The Master initiates a data transfer by creating a START
condition on the bus. The Master then broadcasts an 8-
bit serial Slave address. The four most significant bits of
the Slave address (the
‘
preamble
’
) are fixed to 1010
(Ah), for normal read/write operations and 0110 (6h) for
Software Write Protect (SWP) operations (Fig. 5). The
next three bits, A
2
, A
1
and A
0
, select one of eight possible
Read (1) or Write (0) operation is to be performed.
Acknowledge
After processing the Slave address, the Slave responds
with an acknowledge (ACK) by pulling down the SDA
line during the 9
th
clock cycle. The Slave will aslo
acknowledge the 8-bit byte address and every data byte
presented in WRITE mode. In READ mode the Slave
shifts out eight bits of data, and then
‘
releases
’
the SDA
line durng the 9
th
clock cycle. If the Master acknowledges
in the 9
th
clock cycle (by pulling down the SDA line), then
the Slave continues transmitting. When data transfer is
complete, the Master responds with a NoACK (it does
not acknowledge the last data byte) and the Slave stops
transmitting and waits for a STOP condition.
Figure 4. Acknowledge Timing
Figure 5. Slave Address Bits
ACKNOWLEDGE
1
START
SCL FROM
MASTER
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
1
DEVICE ADDRESS
0
1
0
A2
A1
A0
R/W
0
1
1
0
A2
A1
A0
R/W
Normal Read and Write
Programming the Write
Protect Register
相關PDF資料 |
PDF描述 |
|---|---|
| CAT34RC02JETE13REV-E | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| CAT34RC02WITE13REV-E | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| CAT34RC02YETE13REV-E | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| CAT34RC02YITE13REV-E | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| CAT34RC02PITE13REV-E | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT34RC02YI-TE13 | 制造商:ON Semiconductor 功能描述:EEPROM Serial-I2C 2K-Bit 256 x 8 1.8V/2.5V/3.3V/5V 8-Pin TSSOP T/R |
| CAT34RC02YITE13REV-E | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:2-kb I2C Serial EEPROM, Serial Presence Detect |
| CAT34TS00VP2GT4A | 功能描述:SENSOR TEMP I2C/SMBUS 8TDFN 制造商:on semiconductor 系列:- 零件狀態:在售 傳感器類型:數字，本地 檢測溫度 - 本地:-20°C ~ 125°C 檢測溫度 - 遠程:- 輸出類型:I2C 電壓 - 電源:1.7 V ~ 1.9 V 分辨率:12 b 精度 - 最高（最低）:±1°C（±3°C） 測試條件:-20°C ~ 125°C 工作溫度:-20°C ~ 125°C 安裝類型:表面貼裝 標準包裝:4,000 |
| CAT34TS02 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Digital Output Temperature Sensor with On-board SPD EEPROM |
| CAT34TS02_13 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Digital Output Temperature Sensor with On-board SPD EEPROM |
發布緊急采購，3分鐘左右您將得到回復。