- 您現在的位置：買賣IC網 > PDF目錄374140 > CAT33C804A 4K-Bit Secure Access Serial E2PROM PDF資料下載
參數資料
| 型號： | CAT33C804A |
| 英文描述： | 4K-Bit Secure Access Serial E2PROM |
| 中文描述： | 4K的位安全接入串行E2PROM |
| 文件頁數： | 10/14頁 |
| 文件大小： | 89K |
| 代理商： | CAT33C804A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁
Preliminary
CAT33C804A
10
Doc. No. 25044-00 2/98
As shipped from the factory, the device is in the unpro-
tected mode. The length of the access code is user
selectable from a minimum of one byte to a maximum of
eight bytes (> 1.84x10
19
combinations). Loading a zero-
length access code will disable protection.
MEMORY POINTER REGISTER
The memory pointer enables the user to segment the
E
2
PROM array into two sections. In the unprotected
mode, the array can be segmented between read-only
and full access, while in the secure mode, the memory
may be segmented between read-only access and
password-only access. Three instructions are dedicated
to the memory pointer operations. The first one is WMPR
(Write Memory Pointer Register). This instruction, fol-
lowed by an address, will load the memory pointer
register with a new address. This address will be stored
in the E
2
PROM and can be modified only by another
WMPR instruction. The second instruction is OVMPR
(Override Memory Pointer Register) which allows a
single program/erase to be performed to memory loca-
tions below the address set in the memory pointer. This
instruction allows the user to modify data in a segmented
array without having to move the memory pointer. Once
the operation is complete, the device returns to the
protected mode. If the device is in the secure mode both
of these instructions require the ENAC instruction and a
valid access code prior to their execution. The third
instruction is the RMPR (Read Memory Pointer Regis-
ter) which will place the current contents of the register
in the serial output buffer.
STATUS REGISTER
An eight bit status register is provided to allow the user
to determine the status of the CAT33C804A. The con-
tents of the first three bits of the register are 101 which
allows the user to quickly determine the condition of the
device. The next three bits indicate the status of the
device; they are parity error, instruction error and RDY/
BUSY status. The last two bits are reserved for future
use.
CLEAR ALL AND WRITE ALL
As a precaution, the ERAL instruction has to be entered
twice before it is executed. This measure is required as
a redundancy check on the incoming instruction for
possible transmission errors. The WRAL instruction
requires sending an ERAL first (this sets a flag only) and
Figure 11. Erase Timing (x8 Format)
33C804 F12
Figure 12. Erase Timing (x16 Format)
33C804 F13
Note:
(1)
DO becomes low to indicate busy status if ENBSY was previously executed. If ENBSY was not previously executed, DO will be in High-Z
condition.
CS
DI
HIGH-Z
DO
OP0–OP7
tEW
BUSY(1)
OP CODE
A8–A15
ADDRESS
A0–A7
ADDRESS
NEXT INSTRUCTION
CS
DI
HIGH-Z
DO
OP0–OP7
tEW
BUSY(1)
OP CODE
A0–A7
ADDRESS
NEXT INSTRUCTION
相關PDF資料 |
PDF描述 |
|---|---|
| CAT33C804AJ-TE13 | 4K-Bit Secure Access Serial E2PROM |
| CAT33C804AJA-TE13 | 4K-Bit Secure Access Serial E2PROM |
| CAT33C804AJI-TE13 | 4K-Bit Secure Access Serial E2PROM |
| CAT33C804AP-TE13 | 4K-Bit Secure Access Serial E2PROM |
| CAT33C804APA-TE13 | 4K-Bit Secure Access Serial E2PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT33C804ACI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial EEPROM |
| CAT33C804ADI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial EEPROM |
| CAT33C804AJATE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:4K-Bit Secure Access Serial E2PROM |
| CAT33C804AJA-TE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:4K-Bit Secure Access Serial E2PROM |
| CAT33C804AJITE13 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:4K-Bit Secure Access Serial E2PROM |
發布緊急采購，3分鐘左右您將得到回復。