參數資料
型號: CAT25C03L-1.8TE13
元件分類: EEPROM
英文描述: 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM
中文描述: 1K/2K/4K/8K/16K SPI 串行 互補型金屬氧化物 電可擦可編程只讀存儲器
文件頁數: 6/12頁
文件大?。?/td> 79K
代理商: CAT25C03L-1.8TE13
6
CAT25C11/03/05/09/17
Doc. No. 1017, Rev. J
Figure 2. WREN Instruction Timing
Figure 3. WRDI Instruction Timing
operation to the status register. The
WP
pin function is
blocked when the WPEN bit is set to 0. Figure 10 illustrates
the
WP
timing sequence during a write operation.
HOLD
:
Hold
HOLD
is the HOLD pin. The
HOLD
pin is used to pause
transmission to the CAT25C11/03/05/09/17 while in the
middle of a serial sequence without having to re-transmit
entire sequence at a later time. To pause,
HOLD
must be
brought low while SCK is low. The SO pin is in a high
impedance state during the time the part is paused, and
transitions on the SI pins will be ignored. To resume
communication,
HOLD
is brought high, while SCK is low.
HOLD
should be held high any time this function is not
being used.
HOLD
may be tied high directly to V
CC
or tied
to V
CC
through a resistor. Figure 9 illustrates hold timing
sequence.
STATUS REGISTER
The Status Register indicates the status of the device.
The
RDY
(Ready) bit indicates whether the CAT25C11/
SK
SI
CS
SO
0
0
0
0
0
1
1
0
HIGH IMPEDANCE
SK
SI
CS
SO
0
0
0
0
0
1
0
0
HIGH IMPEDANCE
Note: Dashed Line= mode (1, 1)
Note: Dashed Line= mode (1, 1)
03/05/09/17 is busy with a write operation. When set to
1 a write cycle is in progress and when set to 0 the device
indicates it is ready. This bit is read only the WEL (Write
Enable) bit indicates the status of the write enable latch.
When set to 1, the device is in a Write Enable state and
when set to 0 the device is in a Write Disable state. The
WEL bit can only be set by the WREN instruction and can
be reset by the WRDI instruction.
The BP0, BP1 and BP2 bits indicate which part of the
memory array is currently protected. These bits are set
by the user issuing the WRSR instruction. The user is
allowed to protect from one page to as much as half the
entire array. Once the three protection bits are set the
associated memory can be read but not written until the
protection bits are reset. These bits are non volatile.
The WPEN (Write Protect Enable) is an enable b it for the
WP
pin. The
WP
pin and WPEN bit in the status register
control the programmable hardware write protect fea-
ture. Hardware write protection is enabled when
WP
is
low and WPEN bit is set to high. The user cannot write
to the status register, (including the block protect bits
相關PDF資料
PDF描述
CAT25C05L-1.8TE13 PT 4C 4#20 SKT PLUG
CAT25C09LA-1.8TE13 BNC RECPT #1 FLANGE TURRET
CAT25C09LA-TE13 RF/Coaxial Connector; RF Coax Type:BNC; Contact Termination:Solder; Impedance:50ohm; Body Style:Straight Bulkhead Jack; RG Cable Type:58, 59, 179, 316 RoHS Compliant: Yes
CAT25C03LA-TE13 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM
CAT25C05LA-1.8TE13 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM
相關代理商/技術參數
參數描述
CAT25C03LA 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
CAT25C03LI 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
CAT25C03P 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
CAT25C03P-1.8 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 1.8-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
CAT25C03PA 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8