- 您現在的位置：買賣IC網 > PDF目錄366706 > CAT25C02 2K SPI Serial CMOS EEPROM(2K位（256字x8位）SPI串行CMOS EEPROM) PDF資料下載
參數資料
| 型號： | CAT25C02 |
| 英文描述： | 2K SPI Serial CMOS EEPROM(2K位（256字x8位）SPI串行CMOS EEPROM) |
| 中文描述： | 2K SPI串行EEPROM中的CMOS（2K位（256字x8位）的SPI串行EEPROM中的CMOS） |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 59K |
| 代理商： | CAT25C02 |
4
CAT25C01/02/04/08/16
Doc. No. 25067-00 5/00
Advanced Information
FUNCTIONAL DESCRIPTION
The CAT25C01/02/04/08/16 supports the SPI bus data
transmission protocol. The synchronous Serial Periph-
eral Interface (SPI) helps the CAT25C01/02/04/08/16 to
interface directly with many of today
’
s popular
microcontrollers. The CAT25C01/02/04/08/16 contains
an 8-bit instruction register. (The instruction set and the
operation codes are detailed in the instruction set table)
After the device is selected with
CS
going low, the first
byte will be received. The part is accessed via the SI pin,
with data being clocked in on the rising edge of SCK.
The first byte contains one of the six op-codes that define
the operation to be performed.
PIN DESCRIPTION
SI:
Serial Input
SI is the serial data input pin. This pin is used to input all
opcodes, byte addresses, and data to be written to the
25C01/02/04/08/16. Input data is latched on the rising
edge of the serial clock for SPI modes (0, 0 & 1, 1).
SO:
Serial Output
SO is the serial data output pin. This pin is used to
transfer data out of the 25C01/02/04/08/16. During a
read cycle, data is shifted out on the falling edge of the
serial clock for SPI modes (0,0 & 1,1).
SCK:
Serial Clock
SCK is the serial clock pin. This pin is used to synchro-
nize the communication between the microcontroller
and the 25C01/02/04/08/16. Opcodes, byte addresses,
or data present on the SI pin are latched on the rising
edge of the SCK. Data on the SO pin is updated on the
falling edge of the SCK for SPI modes (0,0 & 1,1) .
CS
:
Chip Select
CS
is the Chip select pin.
CS
low enables the CAT25C01/
02/04/08/16 and
CS
high disables the CAT25C01/02/
04/08/16.
CS
high takes the SO output pin to high
impedance and forces the devices into a Standby Mode
(unless an internal write operation is underway) The
CAT25C01/02/04/08/16 draws ZERO current in the
Standby mode. A high to low transition on
CS
is required
prior to any sequence being initiated. A low to high
transition on
CS
after a valid write sequence is what
initiates an internal write cycle.
WP
:
Write Protect
WP
is the Write Protect pin. The Write Protect pin will
allow normal read/write operations when held high.
When
WP
is tied low and the WPEN bit in the status
register is set to
“
1
”
, all write operations to the status
register are inhibited.
WP
going low while
CS
is still low
will interrupt a write to the status register. If the internal
write cycle has already been initiated,
WP
going low will
have no effect on any write operation to the status
register. The
WP
pin function is blocked when the WPEN
bit is set to 0. Figure 10 illustrates the
WP
timing
sequence during a write operation.
Instruction
Opcode
Operation
WREN
0000 0110
Enable Write Operations
WRDI
0000 0100
Disable Write Operations
RDSR
0000 0101
Read Status Register
WRSR
0000 0001
0000 X011
(1)
0000 X010
(1)
Write Status Register
READ
Read Data from Memory
WRITE
Write Data to Memory
INSTRUCTION SET
Note:
(1) X=0 for 25C01, 25C02, 25C08, 25C16. X=A8 for 25C04
(2) This parameter is tested initially and after a design or process change that affects the parameter.
(3) t
PUR
and t
PUW
are the delays required from the time V
CC
is stable until the specified operation can be initiated.
Power-Up Timing
(2)(3)
Symbol
Parameter
Max.
Units
t
PUR
t
PUW
Power-up to Read Operation
Power-up to Write Operation
1
1
ms
ms
相關PDF資料 |
PDF描述 |
|---|---|
| CAT25C03L-1.8TE13 | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
| CAT25C05L-1.8TE13 | PT 4C 4#20 SKT PLUG |
| CAT25C09LA-1.8TE13 | BNC RECPT #1 FLANGE TURRET |
| CAT25C09LA-TE13 | RF/Coaxial Connector; RF Coax Type:BNC; Contact Termination:Solder; Impedance:50ohm; Body Style:Straight Bulkhead Jack; RG Cable Type:58, 59, 179, 316 RoHS Compliant: Yes |
| CAT25C03LA-TE13 | 1K/2K/4K/8K/16K SPI Serial CMOS EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT25C02L | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C02L-1.8 | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 1.8-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C02LA | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C02LI | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT25C02P | 功能描述:電可擦除可編程只讀存儲器 (256x8) 2K 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。