
2
CAT25010/20/40
Doc. No. 1006, Rev. L
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................
–
55
°
C to +125
°
C
Storage Temperature.......................
–
65
°
C to +150
°
C
Voltage on any Pin with
Respect to V
SS(1)
..................
–
2.0V to +V
CC
+2.0V
V
CC
with Respect to V
SS................................
–
2.0V to +7.0V
Package Power Dissipation
Capability (Ta = 25
°
C)................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300
°
C
Output Short Circuit Current
(2)
........................ 100 mA
*COMMENT
Stresses above those listed under
“
Absolute Maximum
Ratings
”
may cause permanent damage to the device.
These are stress ratings only, and functional operation
of the device at these or any other conditions outside of
those listed in the operational sections of this specifica-
tion is not implied. Exposure to any absolute maximum
rating for extended periods may affect device perfor-
mance and reliability.
RELIABILITY CHARACTERISTICS
Symbol
N
END(3)
Parameter
Min.
Max.
Units
Reference Test Method
Endurance
1,000,000
Cycles/Byte
MIL-STD-883, Test Method 1033
T
DR(3)
Data Retention
100
Years
MIL-STD-883, Test Method 1008
V
ZAP(3)
ESD Susceptibility
2000
Volts
MIL-STD-883, Test Method 3015
I
LTH(3)(4)
Latch-Up
100
mA
JEDEC Standard 17
Note:
(1) The minimum DC input voltage is
–
0.5V. During transitions, inputs may undershoot to
–
2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V
CC
+0.5V, which may overshoot to V
CC
+2.0V for periods of less than 20 ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from
–
1V to V
CC
+1V.
(5) V
IL
min and V
IH
max are reference values only and are not tested.
(6) Maximum standby current (I
SB
) = 10
μ
A for the Automotive and Extended Automotive temperature range.
D.C. OPERATING CHARACTERISTICS
V
CC
= +1.8V to +6.0V, unless otherwise specified.
Limits
Typ.
Symbol
Parameter
Min.
Max.
Units
Test Conditions
I
CC1
Power Supply Current
(Operating Write)
5
mA
V
CC
= 5V @ 5MHz
SO=open; CS=Vss
I
CC2
Power Supply Current
(Operating Read)
3
mA
V
CC
= 5.5V
F
CLK
= 5MHz
I
SB(6)
Power Supply Current
(Standby)
1
μ
A
CS
= V
CC
V
IN
= V
SS
or V
CC
V
IN
= V
SS
or V
CC
V
OUT
= 0V to V
CC
,
CS = 0V
I
LI
I
LO
Input Leakage Current
2
μ
A
μ
A
Output Leakage Current
3
V
IL(5)
V
IH(5)
V
OL1
V
OH1
Input Low Voltage
-1
V
CC
x 0.3
V
CC
+ 0.5
0.4
V
Input High Voltage
V
CC
x 0.7
V
Output Low Voltage
V
Output High Voltage
V
CC
- 0.8
V
V
OL2
V
OH2
Output Low Voltage
0.2
V
1.8V
≤
V
CC
<2.7V
I
OL
= 150
μ
A
I
OH
= -100
μ
A
Output High Voltage
V
CC
-0.2
V
2.7V
≤
V
CC
<5.5V
I
OL
= 3.0mA
I
OH
= -1.6mA