- 您現在的位置：買賣IC網 > PDF目錄366692 > CAT24WC05U 2K/4K/8K/16K-Bit Serial E2PROM PDF資料下載
參數資料
| 型號： | CAT24WC05U |
| 英文描述： | 2K/4K/8K/16K-Bit Serial E2PROM |
| 中文描述： | 2K/4K/8K/16K-Bit串行E2PROM |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 43K |
| 代理商： | CAT24WC05U |
CAT24WC03/05/09/17
6
Doc. No. 25063-00 2/98 S-1
Preliminary
most significant bits of the 8-bit slave address are fixed
as 1010 for the CAT24WC03/05/09/17 (see Fig. 5). The
next three significant bits (A2, A1, A0) are the device
address bits and define which device or which part of the
device the Master is accessing. Up to eight CAT24WC03,
four CAT24WC05, two CAT24WC09, and one
CAT24WC17 may be individually addressed by the
system. The last bit of the slave address specifies
whether a Read or Write operation is to be performed.
When this bit is set to 1, a Read operation is selected,
and when set to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT24WC03/05/09/17 monitors the
bus and responds with an acknowledge (on the SDA
line) when its address matches the transmitted slave
address. The CAT24WC03/05/09/17 then performs a
Read or Write operation depending on the state of the
R/
W
bit.
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledg-
ing device pulls down the SDA line during the ninth clock
cycle, signaling that it received the 8 bits of data.
The CAT24WC03/05/09/17 responds with an acknowl-
edge after receiving a START condition and its slave
address. If the device has been selected along with a
write operation, it responds with an acknowledge after
receiving each 8-bit byte.
When the CAT24WC03/05/09/17 is in a READ mode it
transmits 8 bits of data, releases the SDA line, and
monitors the line for an acknowledge. Once it receives
this acknowledge, the CAT24WC03/05/09/17 will con-
tinue to transmit data. If no acknowledge is sent by the
Master, the device terminates data transmission and
waits for a STOP condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/
W
bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
the byte address that is to be written into the address
pointer of the CAT24WC03/05/09/17. After receiving
another acknowledge from the Slave, the Master device
transmits the data byte to be written into the addressed
memory location. The CAT24WC03/05/09/17 acknowl-
edge once more and the Master generates the STOP
condition, at which time the device begins its internal
programming cycle to nonvolatile memory. While this
internal cycle is in progress, the device will not respond
to any request from the Master device.
Page Write
The CAT24WC03/05/09/17 writes up to 16 bytes of data
in a single write cycle, using the Page Write operation.
The Page Write operation is initiated in the same manner
as the Byte Write operation, however instead of termi-
nating after the initial word is transmitted, the Master is
allowed to send up to 15 additional bytes. After each byte
has been transmitted the CAT24WC03/05/09/17 will
respond with an acknowledge, and internally increment
24WCXX F09
Figure 7. Page Write Timing
BYTE
ADDRESS
SLAVE
ADDRESS
S
A
C
K
A
C
K
DATA
A
C
K
S
T
O
P
P
BUS ACTIVITY:
MASTER
SDA LINE
S
T
A
R
T
5020 FHD F08
Figure 6. Byte Write Timing
BUS ACTIVITY:
MASTER
SDA LINE
DATA n+P
BYTE
ADDRESS (n)
A
C
K
A
C
K
DATA n
A
C
K
S
T
O
P
24WCXX FO9
S
A
C
K
DATA n+1
A
C
K
S
T
A
R
T
P
SLAVE
ADDRESS
NOTE: IN THIS EXAMPLE n = XXXX 0000(B); X = 1 or 0
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24WC08YATE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC08UETE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC08UITE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC08WATE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
| CAT24WC08WETE13F | 1K/2K/4K/8K/16K-Bit Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24WC05U-1.8 | 功能描述:電可擦除可編程只讀存儲器 (512x8) 4k 1.8-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC05UA | 功能描述:電可擦除可編程只讀存儲器 (512x8) 4k 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC05UI | 功能描述:電可擦除可編程只讀存儲器 (512x8) 4k 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC05UI-1.8 | 功能描述:電可擦除可編程只讀存儲器 (512x8) 4k 1.8-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24WC05W | 功能描述:電可擦除可編程只讀存儲器 (512x8) 4k 2.5-6.0 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。