- 您現在的位置：買賣IC網 > PDF目錄366690 > CAT24FC16GD4ITE13 16-kb I2C Serial EEPROM PDF資料下載
參數資料
| 型號： | CAT24FC16GD4ITE13 |
| 元件分類： | EEPROM |
| 英文描述： | 16-kb I2C Serial EEPROM |
| 中文描述： | 16 KB的的I2C串行EEPROM |
| 文件頁數： | 5/11頁 |
| 文件大小： | 601K |
| 代理商： | CAT24FC16GD4ITE13 |
DsconinuedPat
START
CAT24FC16
5
Doc No. 1054, Rev. I
I
2
C BUS PROTOCOL
The following defines the features of the I
2
C bus proto-
col:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes
in the data line while the clock line is high will be
interpreted as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT24FC16 monitor the
SDA and SCL lines and will not respond until this
condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master then sends the address of the
particular slave device it is requesting. The four most
significant bits of the 8-bit slave address are fixed as
1010 for the CAT24FC16 (see Fig. 5). The next three
significant bits (A10, A9, A8) are the memory array
address bits. The last bit of the slave address specifies
whether a Read or Write operation is to be performed.
When this bit is set to 1, a Read operation is selected,
and when set to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT24FC16 monitors the bus and
responds with an acknowledge (on the SDA line) when
its address matches the transmitted slave address. The
CAT24FC16 then performs a Read or a Write operation
Acknowledge
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledg-
ing device pulls down the SDA line during the ninth clock
cycle, signaling that it received the 8 bits of data.
The CAT24FC16 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation,
it responds with an acknowledge after receiving each
byte.
When the CAT24FC16 begins a READ mode, it trans-
mits 8 bits of data, releases the SDA line, and monitors
the line for an acknowledge. Once it receives this ac-
knowledge, the CAT24FC16 will continue to transmit
data. If no acknowledge is sent by the Master, the device
terminates data transmission and waits for a STOP
condition.
Figure 4. Acknowledge Timing
Figure 5. Slave Address Bits
ACKNOWLEDGE
1
SCL FROM
MASTER
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
1
DEVICE ADDRESS
0
1
0
A10
A9
A8
R/W
Normal Read and Write
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24FC16GLETE13 | 16-kb I2C Serial EEPROM |
| CAT24FC16GLITE13 | 16-kb I2C Serial EEPROM |
| CAT24FC16GWETE13 | 16-kb I2C Serial EEPROM |
| CAT24FC16GWITE13 | 16-kb I2C Serial EEPROM |
| CAT24FC16GYETE13 | 16-kb I2C Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24FC256JA-1.8 | 功能描述:電可擦除可編程只讀存儲器 256K (32KX8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24FC256JI-1.8 | 功能描述:電可擦除可編程只讀存儲器 256K (32KX8) Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24FC256KI-1.8 | 功能描述:電可擦除可編程只讀存儲器 256K (32KX8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24FC256LI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT24FC256WA-1.8 | 功能描述:電可擦除可編程只讀存儲器 256K (32KX8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。