- 您現在的位置：買賣IC網 > PDF目錄379721 > C7921CA-09 (Hamamatsu Photonics) High resolution and high frame rate PDF資料下載
參數資料
| 型號： | C7921CA-09 |
| 廠商： | Hamamatsu Photonics |
| 英文描述： | High resolution and high frame rate |
| 中文描述： | 高分辨率，高幀頻 |
| 文件頁數： | 4/6頁 |
| 文件大?。?/td> | 127K |
| 代理商： | C7921CA-09 |
Flat panel sensor
C7921CA-09
4
I
System requirements
To operate C7921CA-09 at full performance, the following system and peripherals are required.
· PC: IBM compatible PC running on Windows XP
· Digital frame grabber card: Monochrome 16 bits or more, pixel clock 7 MHz or more, RS-422 interface synchronous signal (See
the frame grabber manual.)
The National Instruments IMAQ PCI-1424 (NI parts No. 777662-01) frame grabber has been verified to successfully acquire 12-
bit digital images from C7921CA-09. The IMAQ PCI-1422 (NI pats No. 777959-01) also acquires satisfactory images from
C7921CA-09. You can utilize the demonstration software that comes with the frame grabber as a simple viewer, to acquire and
save an image. To do so, refer to the frame grabber user’s guide for how to use the camera information file for the demonstration
software.
· Power source: A.vdd = +5.0 ± 0.1 V (700 mA), D.vdd = +5.0 ± 0.1 V (800 mA).
Please use of a series power supply. (Avoid using a switching power supply.) A power cable (terminated with an
FGG.2B.307.CLAD92Z plug at one end and open at the other end; 2 m; see Table 2.), an external trigger cable (terminated with
an FFA.OS.302.CLAC37 plug at one end and open at the other end; 5 m; see table 3.) and an earth cable (AWG 18; 4 m) comes
supplied with C7921CA-09. An optional frame grabber cable for interface with the 36-pin receptacle (see Table 1) on C7921CA-
09 is also available for synchronous signal, video output and external control.
The voltages described above are specified at the flat panel sensor side. The impedance of the power cable attached with the
flat panel sensor is low enough but it causes 0.1 V approx. drop. Therefore the voltage at the power source side should be set
0.1 V higher than the voltage specified above.
Install a noise filter on the AC power input line to prevent surges on the AC line.
To supply the synchronous signal through ExtTrgGrb, apply high level of TTL to ExtTrgLemo and IntExt, or leave them without
connection. On the contrary, to use ExtTrgLemo, set high level to ExtTrgGrb and IntExt, or leave them without connection. The
earth terminal must be connected to a stable earth point to eliminate noise from surroundings.
Table 1:
Pin assignm ent of 36-pin receptacle
Pin No.
Signal
1
Data12+ (MSB)
2
Data11+
3
Data10+
4
Data9+
5
Data8+
6
Data7+
7
Data6+
8
Data5+
9
Data4+
10
Data3+
11
Data2+
12
Data1+(LSB)
13
bin0 (TTL)
14
bin1 (TTL)
15
ExtTrgGrb (TTL)
16
Vsync+
17
Hsync+
18
Pclk+
Unless otherwise noted, signal level is RS-422.
36-pin receptacle: TX20A-36R-D2GF1-A1L made by JAE (Japan Aviation Electronics Industry limited)
Mating plug: TX20A-36PH1-D2P1-D1E made by JAE (Japan Aviation Electronics Industry limited)
Pin No.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Signal
Data12- (MSB)
Data11-
Data10-
Data9-
Data8-
Data7-
Data6-
Data5-
Data4-
Data3-
Data2-
Data1- (LSB)
GND
GND
IntExt (TTL)
Vsync-
Hsync-
Pclk-
Table 2:
Power pin assignm ent and cable color
Pin No.
1
2
3
4
5
6
7
Shield
7-pin power receptacle: ECG.2B.307.CLV made by LEMO S. A.
Mating power plug: FGG.2B.307.CLAD92Z made by LEMO S. A.
Pin No. 1 to 3 are not connected to the electrical circuit inside of flat panel sensor.
Therefore, previous power source and cable for C7921CA-02 can be used without modification.
Color
Brown
Red
Orange
Yellow
Green
Blue
Purple
-
Signal
Reserved
Reserved
Reserved
Analog GND
Analog +5 V
Digital GND
Digital +5 V
Analog GND
Table 3:
External trigger pin assignm ent and cable color
Pin No.
1
2
Shield
2-pin receptacle: ECP.0S.302.CLL made by LEMO S. A.
Mating plug: FFA.0S.302.CLAC37 made by LEMO S. A.
Color
Red
Black
-
Signal
ExtTrgLemo (TTL)
Signal GND
Analog GND
相關PDF資料 |
PDF描述 |
|---|---|
| C7942CA-02 | Acquire digital X-ray image in real time and 170 & 176 mm diagonal size |
| C7943CA-02 | Acquire digital X-ray image in real time and 170 & 176 mm diagonal size |
| C7942CA | Flat panel sensor |
| C7943CA | Flat panel sensor |
| C7942CK-12 | Acquire digital X-ray image in real time and 170 mm diagonal size |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C7931-1032-24D | 制造商:TINNERMAN 功能描述: |
| C7931-1032-3B | 制造商:TINNERMAN 功能描述: |
| C793110324 | 制造商:n/a 功能描述:Ships in 2 days |
| C7931-1032-4 | 制造商:TINNERMAN 功能描述: |
| C7931-632-4 | 制造商:TINNERMAN 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。