- 您現在的位置：買賣IC網 > PDF目錄374054 > C052K102K2X5CM (KEMET Corporation) MILITARY SPECIFCATIONS ON BACK PDF資料下載
參數資料
| 型號： | C052K102K2X5CM |
| 廠商： | KEMET Corporation |
| 英文描述： | MILITARY SPECIFCATIONS ON BACK |
| 中文描述： | 背面軍事SPECIFCATIONS |
| 文件頁數： | 38/40頁 |
| 文件大?。?/td> | 580K |
| 代理商： | C052K102K2X5CM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁
APPLICATION NOTES FOR MULTILAYER CERAMIC CAPACITORS
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
38
KEMET
the aging rates to set factory test limits which will bring the
capacitance within the specified tolerance at some future time,
to allow for customer receipt and use. Typically, the test limits
are adjusted so that the capacitance will be within the specified
tolerance after either 1,000 hours or 100 days, depending on
the manufacturer and the product type.
POWER DISSIPATION
Power dissipation has been empirically determined for
two representative KEMET series: C052 and C062. Power dis-
sipation capability for various mounting configurations is shown
in Table 3. This table was extracted from Engineering Bulletin
F-2013, which provides a more detailed treatment of this sub-
ject.
Note that no significant difference was detected between
the two sizes in spite of a 2 to 1 surface area ratio. Due to the
materials used in the construction of multilayer ceramic capac-
itors, the power dissipation capability does not depend greatly
on the surface area of the capacitor body, but rather on how
well heat is conducted out of the capacitor lead wires.
Consequently, this power dissipation capability is applicable to
other leaded multilayer styles and sizes.
TABLE 3
POWER DISSIPATION CAPABILITY
(Rise in Celsius degrees per Watt)
Power
Dissipation
of C052 & C062
Mounting Configuration
1.00" leadwires attached to binding post
of GR-1615 bridge (excellent heat sink)
90 Celsius degrees
rise per Watt ±10%
0.25" leadwires attached to binding post
of GR-1615 bridge
55 Celsius degrees
rise per Watt ±10%
Capacitor mounted flush to 0.062" glass-
epoxy circuit board with small copper traces
77 Celsius degrees
rise per Watt ±10%
Capacitor mounted flush to 0.062" glass-
epoxy circuit board with four square inches
of copper land area as a heat sink
53 Celsius degrees
rise per Watt ±10%
As shown in Table 3, the power dissipation capability of
the capacitor is very sensitive to the details of its use environ-
ment. The temperature rise due to power dissipation should not
exceed 20°C. Using that constraint, the maximum permissible
power dissipation may be calculated from the data provided in
Table 3.
It is often convenient to translate power dissipation capa-
bility into a permissible AC voltage rating. Assuming a sinu-
soidal wave form, the RMS “ripple voltage” may be calculated
from the following formula:
The data necessary to make this calculation is included in
Engineering Bulletin F-2013. However, the following criteria
must be observed:
1. The temperature rise due to power dissipation
should be limited to 20°C.
2. The peak AC voltage plus the DC voltage must not
exceed the maximum working voltage of the
capacitor.
Provided that these criteria are met, multilayer ceramic
capacitors may be operated with AC voltage applied without
need for DC bias.
RELIABILITY
A well constructed multilayer ceramic capacitor is
extremely reliable and, for all practical purposes, has an infi-
nite life span when used within the maximum voltage and
temperature ratings. Capacitor failure may be induced by sus-
tained operation at voltages that exceed the rated DC voltage,
voltage spikes or transients that exceed the dielectric with-
standing voltage, sustained operation at temperatures above
the maximum rated temperature, or the excessive tempera-
ture rise due to power dissipation.
Failure rate is usually expressed in terms of percent per
1,000 hours or in FITS (failure per billion hours). Some
KEMET series are qualified under U.S. military established
reliability specifications MIL-PRF-20, MIL-PRF-123, MIL-
PRF-39014, and MIL-PRF-55681. Failure rates as low as
0.001% per 1,000 hours are available for all capacitance /
voltage ratings covered by these specifications. These spec-
ifications and
accompanying Qualified Products List should
be consulted for details.
For series not covered by these military specifications,
an internal testing program is maintained by KEMET Quality
Assurance. Samples from each week’s production are sub-
jected to a 2,000 hour accelerated life test at 2 x rated voltage
and maximum rated temperature. Based on the results of
these tests, the average failure rate for all non-military series
covered by this test program is currently 0.06% per 1,000
hours at maximum rated conditions. The failure rate would be
much lower at typical use conditions. For example, using MIL-
HDBK-217D this failure rate translates to 0.9 FITS at 50%
rated voltage and 50°C.
Current failure rate details for specific KEMET multilay-
er ceramic capacitor series are available on request.
MISAPPLICATION
Ceramic capacitors, like any other capacitors, may fail
if they are misapplied. Typical misapplications include expo-
sure to excessive voltage, current or temperature. If the
dielectric layer of the capacitor is damaged by misapplication
the electrical energy of the circuit can be released as heat,
which may damage the circuit board and other components
as well.
If potential for misapplication exists, it is recommended
that precautions be taken to protect personnel and equipment
during initial application of voltage. Commonly used precau-
tions include shielding of personnel and sensing for excessive
power drain during board testing.
E = Z
Where
E = RMS Ripple Voltage (volts)
P = Power Dissipation (watts)
Z = Impedence
R = ESR
P
R
相關PDF資料 |
PDF描述 |
|---|---|
| C056K102K2X5CM | MILITARY SPECIFCATIONS ON BACK |
| C062K102K2X5CM | MILITARY SPECIFCATIONS ON BACK |
| C052T102K2X5CA | MILITARY SPECIFCATIONS ON BACK |
| C056T102K2X5CA | MILITARY SPECIFCATIONS ON BACK |
| C062T102K2X5CA | MILITARY SPECIFCATIONS ON BACK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| C052K102M2X5CA | 功能描述:多層陶瓷電容器MLCC - 含引線 200volts 1000pF 20% RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| C052K102M2X5CA7301 | 功能描述:多層陶瓷電容器MLCC - 含引線 200volts 1000pF 20% RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| C052K102M2X5CATR | 制造商:KEMET Corporation 功能描述:CAP 0.001UF 200VDC X7R 20% RDL 5.08MM - Tape and Reel |
| C052K103K1X5CA | 功能描述:多層陶瓷電容器MLCC - 含引線 100volts .01uF 10% Z5U RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
| C052K103K1X5CA7301 | 功能描述:多層陶瓷電容器MLCC - 含引線 100volts .01uF 10% X7R RoHS:否 制造商:AVX 電容:470 pF 容差:10 % 電壓額定值:3 kV 端接類型:Radial 工作溫度范圍: 溫度系數/代碼:X7R 引線間隔:5.08 mm 產品:Automotive MLCCs 引線類型: |
發布緊急采購，3分鐘左右您將得到回復。