- 您現在的位置：買賣IC網 > PDF目錄385188 > BR9016 (Rohm CO.,LTD.) 8k, 16k bit EEPROMs for direct connection to serial ports PDF資料下載
參數資料
| 型號： | BR9016 |
| 廠商： | Rohm CO.,LTD. |
| 英文描述： | 8k, 16k bit EEPROMs for direct connection to serial ports |
| 中文描述： | 分為8K，16K，可直接連接到串行端口位的EEPROM |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 178K |
| 代理商： | BR9016 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁
BR9080AF-W / BR9080ARFV-W / BR9080ARFVM-W /
Memory ICs
BR9016AF-W / BR9016ARFV-W / BR9016ARFVM-W
!
Operation notes
(1) Turning the power supply on and off
1) When the power supply is turned on and off, CS should be set to HIGH (=V
CC
).
2) When CS is LOW, the command input reception state (active) is entered. If the power supply is turned on in this state,
erroneous operations and erroneous writing can occur because of noise and other factors. To avoid this, make sure
CS is set to HIGH (=V
CC
) before turning on the power supply.
(Good example) Here, the CS pin is pulled up to V
CC
.
When turning off the power supply, wait at least 10msec before turning it on again. Failing to
observe this condition can result in the internal circuit failing to be reset when the power supply is
turned on.
(Bad example) CS is LOW when the power supply is turned on or off.
In this case, because CS remains LOW, the EEPROM may perform erroneous operations or
write erroneous data because of noise or other factors.
* Please be aware that the case shown in this example can also occur if CS input is HIGH-Z.
V
CC
10/12
V
CC
GND
V
CC
GND
CS
Good example
Bad example
Fig.9
(2) Noise countermeasures
1) SK noise
If noise occurs at the rise of the SK clock input, the clock is assumed to be excessive, and this can cause malfunction
because the bits are out of alignment.
2) WC noise
During a writing operation, noise at the WC pin can be erroneously judged to be data, and this can cause writing to be
forcibly interrupted.
3) V
CC
noise
Noise and surges on the power supply line can cause malfunction. We recommend installing a bypass capacitor
between the power supply and ground to eliminate this problem.
相關PDF資料 |
PDF描述 |
|---|---|
| BR9016ARFV-W | 8k, 16k bit EEPROMs for direct connection to serial ports |
| BR9016ARFVM-W | 8k, 16k bit EEPROMs for direct connection to serial ports |
| BR9016F | 8k, 16k bit EEPROMs for direct connection to serial ports |
| BR9040F | 1, 2, and 4k bit EEPROMs for direct connection to serial ports |
| BR9010 | 1, 2, and 4k bit EEPROMs for direct connection to serial ports |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BR9016AF-W | 制造商:ROHM Semiconductor 功能描述:IC,Serial Access EEPROM 1Kx16 SOP8 Seri |
| BR9016AF-WE2 | 功能描述:電可擦除可編程只讀存儲器 SRL 1024X16 BIT RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| BR9016ARFVM-W | 制造商:ROHM 制造商全稱:Rohm 功能描述:8k, 16k bit EEPROMs for direct connection to serial ports |
| BR9016ARFV-W | 制造商:ROHM 制造商全稱:Rohm 功能描述:8k, 16k bit EEPROMs for direct connection to serial ports |
| BR9016ARFV-WE2 | 制造商:ROHM Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。