- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2945 (Benchmark Technology Group) Gas Gauge IC with SMBus Interface(Gas Gauge芯片（帶SMBus 接口）) PDF資料下載
參數資料
| 型號： | bq2945 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC with SMBus Interface(Gas Gauge芯片（帶SMBus 接口）) |
| 中文描述： | 氣體計IC，帶有SMBus接口（電量監測計芯片（帶的SMBus接口）） |
| 文件頁數： | 7/32頁 |
| 文件大小： | 256K |
| 代理商： | BQ2945 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
latest measured capacity in the Discharge Count Reg-
ister, representing a discharge from full to below
EDV1. A qualified discharge is necessary for a capac-
ity transfer from the DCR to the FCC register. Once
updated, the bq2945 writes the new FCC to the EE-
PROM. The FCC also serves as the 100% reference
threshold used by the relative state-of-charge calcula-
tion and display.
2.
DesignCapacity (DC):
The DC is the user-specified battery capacity and is
programmed from external EEPROM. The DC also
provides the 100% reference for the absolute dis-
play mode.
3.
RemainingCapacity (RM):
RM counts up during charge to a maximum value of
FCC and down during discharge and self-discharge to
0. RM is set to 000Ah after the EDV1 threshold has
been reached and a valid charge has been detected.
To prevent overstatement of charge during periods
of overcharge, RM stops incrementing when RM =
FCC.
RM may optionally be written to a user-
defined value when fully charged if the battery
pack is under bq2945 charge control. On initializa-
tion, RM is set to the value stored in EE
0x1e—0x1f.
4.
Discharge Count Register (DCR):
The DCR counts up during discharge independent
of RM and can continue increasing after RM has
decremented to 0. Prior to RM = 0 (empty battery),
both discharge and self-discharge increment the
DCR.
After RM = 0, only discharge increments
the DCR. The DCR resets to 0 when RM = FCC.
The DCR does not roll over but stops counting
when it reaches FFFFh.
The DCR value becomes the new FCC value on the
first charge after a qualified discharge to EDV1. A
qualified discharge to EDV1 occurs if all of the fol-
lowing conditions exist:
No valid charge initiations (charges greater than
10mAh), where V
SRO
> +V
SRD
occurred during
the period between RM = FCC and EDV1 de-
tected.
The self-discharge count is not more than
256mAh.
The temperature is
≥
273°K (0°C) when the
EDV1 level is reached during discharge.
The valid discharge flag (VDQ) in FLAGS1 indi-
cates whether the present discharge is valid for an
FCC update. FCC cannot be reduced by more than
256mAh during any single cycle.
Charge Counting
Charge activity is detected based on a positive voltage
on the SR input.
If charge activity is detected, the
bq2945 increments RM at a rate proportional to V
SRO
and, if enabled, activates an LED display. Charge ac-
tions increment the RM after compensation for charge
state and temperature.
7
bq2945
FG294501.eps
Temperature
Compensation
Charge
Current
Discharge
Current
Self-Discharge
Timer
Remaining
Capacity
(RM)
Full
Charge
Capacity
(FCC)
Discharge
Count
Register
(DCR)
<
Qualified
Transfer
+
Temperature, Other Data
+
-
-
+
Inputs
Main Counters
and Capacity
Reference (FCC)
Outputs
Two-Wire
Serial Interface
Chip-Controlled
Available Charge
LED Display
State-of-charge
and
Temperature
Compensation
Figure 2. Operational Overview
相關PDF資料 |
PDF描述 |
|---|---|
| BR-B6134-05V | RESISTOR LED LAMPS (ROUND TYPES) |
| BR-B51V1-05V | RESISTOR LED LAMPS (ROUND TYPES) |
| BR-B61V1-05V | RESISTOR LED LAMPS (ROUND TYPES) |
| BR-B21V1-12V | Metal Oxide Resistor; Series:MP800; Resistance:15ohm; Resistance Tolerance:+/- 1 %; Power Rating:20W; Temperature Coefficient:-20 to +50 ppm/ C; Terminal Type:Radial Leaded; Package/Case:2-TO-220; Voltage Rating:300V |
| BR-BX11V1-12V | Metal Oxide Resistor; Series:MP800; Resistance:15ohm; Resistance Tolerance:+/- 1 %; Power Rating:20W; Temperature Coefficient:-20 to +50 ppm/ C; Terminal Type:Radial Leaded; Package/Case:2-TO-220; Voltage Rating:300V |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ294502 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Overvoltage Protection for 2-Series and 3-Series Cell Li-Ion Batteries |
| BQ294502DRVR | 功能描述:電池管理 Overvltg Prot Device RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ294502DRVT | 功能描述:電池管理 Overvltg Prot Device RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ294502EVM-033 | 功能描述:電源管理IC開發工具 bq294502 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ294504 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Overvoltage Protection for 2-Series and 3-Series Cell Li-Ion Batteries |
發布緊急采購，3分鐘左右您將得到回復。