- 您現在的位置：買賣IC網 > PDF目錄385186 > bq2052 (Benchmark Technology Group) Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) PDF資料下載
參數資料
| 型號： | bq2052 |
| 廠商： | Benchmark Technology Group |
| 英文描述： | Gas Gauge IC for Lithium Primary Cells(Gas Gauge 芯片（用于鋰電池）) |
| 中文描述： | 氣體計IC（電量監測計芯片（用于鋰電池），鋰原電池） |
| 文件頁數： | 12/18頁 |
| 文件大小： | 161K |
| 代理商： | BQ2052 |
In incremental mode (PROG
5
= L), the battery charge
state is displayed on pins SEG1–SEG4. The charge state
condition indicated by each segment is shown in Table 7.
Only the segment pin representing the present remain-
ing capacity is ON (low); all other segments are OFF
(high impedance). When DISP is pulled low, the display
is active for 10s.
Table 7. Incremental Display Mode
PROG
5
= L
SEG Pin ON
Remaining Capacity
90 -100%
50 - < 90%
20 - < 50%
< 20%
V
SB
< V
EDV1
SEG4
SEG3
SEG2
SEG1
SEG1—BLINK
In binary mode (PROG5 = H), the battery charge state is
displayed using only pins SEG1 and SEG2, with the re-
maining capacity indication defined as in Table 8
.
When
DISP is pulled low,the display is active for 4s.
Table 8. Binary Display Mode
PROG
5
= H
SEG 1
ON
ON
OFF
OFF
SEG 2
ON
OFF
ON
OFF
Remaining Capacity
70 -100%
40 - < 70%
10 - < 40%
< 10% or V
SB
< V
EDVF
In bar graph mode (PROG
5
= Z), the battery charge
state is displayed using pins SEG1 through SEG 5 ac-
cording to Table 9. When DISP is pulled low, the display
is active for 4s.
Microregulator
A micro-power source for the bq2052 can be inexpen-
sively built using a FET and an external resistor as
shown in Figure 1.
RBI Input
The RBI input pin should be used with a storage capaci-
tor or external supply to provide backup potential to the
internal bq2052 registers when V
CC
drops below 3.0V.
V
CC
is output on RBI when V
CC
is above 3.0V. If using
an external supply (such as the bottom series cell) as the
backup source, an external diode is required for isola-
tion.
Initialization
The bq2052 can be initialized by removing V
CC
and
grounding the RBI pin for 5s or by a command over the
serial port.
The serial port reset command requires
writing 78h to register CMDWD (address = 00h).
On initialization with PROG6 = H, the bq2052 sets the
registers as
FNAC = PFC
CACH = PFC
CACL = 0x00
RCAC = 0x64
FLGS1 = 0x90
12
bq2052
Preliminary
Table 9. Bar Graph Display Mode
PROG
5
= Z
SEG1
ON
ON
ON
ON
ON
BLINK
SEG2
ON
ON
ON
ON
OFF
OFF
SEG3
ON
ON
ON
OFF
OFF
OFF
SEG4
ON
ON
OFF
OFF
OFF
OFF
SEG5
ON
OFF
OFF
OFF
OFF
OFF
Remaining Capacity
80 - 100%
60 - < 80%
40 - < 60%
20 - < 40%
< 20%
VSB < VEDV1
相關PDF資料 |
PDF描述 |
|---|---|
| bq2060 | SBS v1.1-Compliant Gas Gauge IC(Gas Gauge芯片) |
| bq2092 | Gas Gauge IC with SMBus-Like Interface(Gas Gauge芯片（帶SMBus 接口）) |
| bq2201 | SRAM Nonvolatile Controller Unit(靜態RAM非易失性控制器單元) |
| bq2202 | SRAM Nonvolatile Controller With Reset(靜態RAM非易失性控制器單元(帶復位）) |
| bq2502 | Integrated Backup Unit(完整的后備單元) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BQ2052EVM-001 | 功能描述:電源管理IC開發工具 BQ2052 Eval Kit for Primary Lithium 15V RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| BQ2052SN | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Gas Gauge IC for Lithium Primary Cells |
| BQ2052SNA515 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| BQ2052SN-A515 | 功能描述:電池管理 Primary Lithium Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| BQ2052SN-A515G4 | 功能描述:電池管理 Prim Lith Gas Gauge RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。