- 您現在的位置：買賣IC網 > PDF目錄385183 > BP5250 (Rohm CO.,LTD.) 25 AMP MINIATURE POWER RELAY PDF資料下載
參數資料
| 型號： | BP5250 |
| 廠商： | Rohm CO.,LTD. |
| 英文描述： | 25 AMP MINIATURE POWER RELAY |
| 中文描述： | 直流/直流轉換器 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 118K |
| 代理商： | BP5250 |
BP5250 / BP5250-24
(5) Overcurrent detection resisor(R1)
Overcurrent detection resistor is determined by the
following expression.
R1=VLT1/Iomax [m
]
VLT1 : Overcurrent offset voltage1(60
～
76mV)
Iomax : Maximum overload current [A]
And, ISL current at short circuit is
ISL=VLT2/R1 [A]
VLT2 : Overcurrent detection offset voltage2(20
～
36mV)
From the above-mentioned, fold-back current characteristic when the overcurrent protection is
operated is shown. Both Iomax, and ISL may be different value from the actual value because they are
detected at the peak current. Please make sure to confirm it in the actual operating.
(6) Input smoothing capacitor(C1)
Large ripple current flow into the input smoothing capacitor. The current is determined by the following
expression. For actual usage, please use the larger one than this numeric value.
Output current [Io]
Overcurrent protection characteristic
O
Vo
I
SL
Iomax
Irms=ir
×
Vo/3Vi
+
(ip-ir)
×
Vo/Vi [A]
Irms : Input ripple current actual-value [Arms]
ir
: Ripple current [A]
ip
: Peak current [A]
V
: Input voltage [V]
Vo
: Output voltage [V]
· Voltage of the used capacitor must be more than Vi
×
2.
· Allowable ripple current of the used capacitor must be larger than the ripple current.
(7) Output smoothing capacitor(C2)
Output smoothing capacitor is determined by the impedance of smoothing capacitor from the mark value of
output ripple voltage.
Zc
≤
Vr/ir [
]
Zc : Impedance of capacitor [
]
Vr : Mark value of output ripple voltage[Vp-p]
ir
: Ripple current [A]
· Voltage of the used capacitor must be more than Vo
×
2.
· Allowable ripple current of the used capacitor must be larger than the ripple current.
(4) Flywhell diode(SD1)
· Rated current must be twice as much as the maximum overload
current(Iomax) or more.
· Rated voltage must be 1.3 times as much as the maximum input
voltage or more.
· Please use the high-speed switching schottky barrierdiode that
reverse recovery time is 50ns or less.
· If it used in high temperature, please be careful about the
temperature characteristics of IR.
Input voltage Vi [V]
Input voltage VS. DC reverse voltage
D 50
40
30
20
10
05
25
30
10
15
20
7/11
相關PDF資料 |
PDF描述 |
|---|---|
| BP5250-24 | 25 AMP MINIATURE POWER RELAY |
| BPD-HQB33 | SURFACE MOUNT PHOTO DIODES |
| BPD-HQA33 | SURFACE MOUNT PHOTO DIODES |
| BPD-RQ09DV-1 | SIDE- LOOK PACKAGE PIN PHOTO DIODE |
| BPI-3C1-01 | LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BP5250-24 | 功能描述:電壓監測器/監控器 DC/DC 24V RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| BP5255BR00SP | 制造商:POWGG 功能描述: |
| BP5275-18 | 功能描述:直流/直流開關轉換器 3Term Step Dwn DC/DC Cnvrtr Non-Iso 1.8V RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| BP5275-25 | 功能描述:直流/直流開關轉換器 3Term Step Dwn DC/DC Cnvrtr Non-Iso 2.5V RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| BP5275-33 | 功能描述:直流/直流開關轉換器 3Term Step Dwn DC/DC Cnvrtr Non-Iso 3.3V RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。