參數資料
型號： BM29F400T-15TC
英文描述： x8/x16 Flash EEPROM
中文描述： x8/x16閃存EEPROM
文件頁數： 10/37頁
文件大?。?/td> 265K
代理商： BM29F400T-15TC
BRIGHT
Microelectronics
Inc.
BM29F400T/BM29F400B
- 10 -
Multiple sectors can be erased simultaneously by writing the sixth bus cycle command of the Sector
Erase command for each sector to be erased. The time between initiation of the next Sector Erase
command must be less than 80
μ
S to guarantee acceptance of the command by the internal state
machine. The time-out window can be monitored via the write operation status pin DQ3 (refer to the
Write Operation Status section for Sector Erase Timer operation). It is recommended that CPU
interrupts be disabled during this time to ensure that the subsequent Sector Erase commands can be
initiated within the 100
μ
S window. The interrupts can be re-enabled after the last Sector Erase
command is written. As mentioned above, an internal device timer will initiate the Sector Erase
operation 100
μ
S
±
20% (80
μ
S to 120
μ
S) from the rising edge of the last WE pulse. Sector Erase
Timer Write Operation Status pin (DQ3) can be used to monitor time out window. If another falling
edge of the WE occurs within the 100 mS time-out window, the internal device timer is reset.
Loading the sector erase buffer may be done in any sequence and with any number of sectors.
Any command other than Sector Erase or Erase Suspend during this period and afterwards will
RESET
the device to read mode, ignoring the previous command string. Resetting the device with a
hardware RESET after it has begun execution of a Sector Erase operation will result in the data in
the operated sectors being undefined and may be unrecoverable. In this case, restart the Sector
Erase operation on those sectors and attempt to allow them to complete the Erase operation.
Command Definitions
Device operations are selected by writing specific address and data sequences in to the Command
register. Writing incorrect addresses and data values or writing them in the improper sequence will
RESET
the device to Read mode. Table 5 defines the valid register command sequences. Either of
the two Read/Reset commands will
RESET
the device (when applicable).
During Sector Erase operation, data bit DQ7 shows a logical "0". This operation is known as Data
Polling. Sector Erase operation is complete when data on DQ7 is a logical "1" (see Write Operation
Status section) at which time the device returns to read mode. At this time, the address pins are no
longer latched. Note that Data Polling must be performed at a sector address within any of the
sectors being erased and not a protected sector to ensure that DQ7 returns a logical "1" upon
completion of the Sector Erase operation.
Figure 2 illustrates the Sector Erase Algorithm using typical command strings and bus operations.
During execution of the Sector Erase command, only the Erase Suspend and Erase Resume
commands are allowed. All other commands will
RESET
the device to read mode.
Note: Do not attempt to write an invalid command sequence during the sector erase operation. Doing so will terminate the sector
erase operation and the device will /RESET to the read mode.
相關PDF資料
PDF描述
BM29F400T-90TC x8/x16 Flash EEPROM
BMS-SAX300MM GUIDE PCB 300MM STRIP
BN101 Optoelectronic
BN201 Optoelectronic
BN301 Optoelectronic
相關代理商/技術參數
參數描述
BM29F400T-90TC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8/x16 Flash EEPROM
BM-2A 制造商:Anderson Power Products (APP) 功能描述:BENCH MOUNT
BM-2BK 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CASE DESKTOP
BM2LB150FJ-CE2 功能描述:2CH LOW SIDE SWITCH IC, 150M OHM 制造商:rohm semiconductor 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOP-J 標準包裝:1
BM2LB300FJ-CE2 功能描述:THE BM2LB300FJ-C IS AN AUTOMOTIV 制造商:rohm semiconductor 系列:* 包裝:剪切帶（CT） 零件狀態:在售 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOP-J 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*