- 您現在的位置：買賣IC網 > PDF目錄385169 > BL34018 (上海貝嶺股份有限公司) BL34018 PDF資料下載
參數資料
| 型號： | BL34018 |
| 廠商： | 上海貝嶺股份有限公司 |
| 英文描述： | BL34018 |
| 中文描述： | BL34018 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 586K |
| 代理商： | BL34018 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
BL34018
http://www.belling.com.cn
- 2 -
8/15/2006
Wrote by 2006
Total
16 Pages
4. PIN CONFIGURATIONS
Pin
Name
Description
1
RR
A resistor to ground provides a reference current for the transmit and receive attenuators.
2
RTX
A resistor to ground determines the nominal gain of the transmit attenuator. The transmit
channel gain is inversely proportional to the RTX resistance.
3
TXI
Input to the transmit attenuator. Input resistance is nominally 5.0 k ohms.
4
TXO
Output of the transmit attenuator. The TXO output signal drives the input of the transmit
level detector, as well as the external circuit which drives the telephone line.
5
TLI
Input of the transmit level detector. An external resistor ac coupled to the TLI pin sets the
detection level. Decreasing this resistor increases the sensitivity to transmit channel
signals.
6
TLO
Output of the transmit level detector. The external resistor and capacitor set the time the
comparator will hold the system in the transmit mode after speech ceases.
7
RLI
Input of the receive level detector. An external resistor ac coupled to the RLI pin sets the
detection level. Decreasing this resistor increases the sensitivity to receive channel
signals.
8
RLO
Output of the receive level detector. The external resistor and capacitor set the time the
comparator will hold the system in the receive mode after speech ceases.
9
MCI
Microphone amplifier input. Input impedance is nominally 10 k ohms and the dc bias
voltage is approximately equal to VB.
10
MCO
Microphone amplifier output. The mic amp gain is internally set at 34 dB (50V/V).
11
CP1
A parallel resistor and capacitor connected between this pin and VCC holds a voltage
corresponding to the background noise level. The transmit detector compares the CP1
voltage with the speech signal from CP2.
12
CP2
A capacitor at this pin peak detects the speech signals for comparison with the
background noise level held at CP1.
13
XDI
Input to the transmit detector system. The microphone amplifier output is ac coupled to
the XDI pin through an external resistor.
14
SKG
High current ground pin for the speaker amp output stage. The SKG voltage should be
within 10 mV of the ground voltage at Pin 22.
15
SKO
Speaker amplifier output. The SKO pin will source and sink up to 100 mA when ac
coupled to the speaker. The speaker amp gain is internally set at 34 dB (50V/V).
16
V+
Input dc supply voltage. V+ can be powered from Tip and Ring if an ac decoupling
inductor is used to prevent loading ac line signals. The required V+ voltage is 6.0 to 11 V
(7.5 V nominal) at 7.0 mA.
17
AGC
A capacitor from this pin to VB stabilizes the speaker amp gain control loop and
相關PDF資料 |
PDF描述 |
|---|---|
| BL34118 | Voice Switched Speakerphone Circuit |
| BL3501 | BL3501 |
| BL3502S | BL3502S |
| BL35P12 | BL35P12 |
| BL431-CPRM | Adjustable shunt regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BL3406B | 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:1.5 MHz, 800mA Synchronous Buck Converter |
| BL34118 | 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:Voice Switched Speakerphone Circuit |
| BL3501 | 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:BL3501 |
| BL3502S | 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:BL3502S |
| BL35P02 | 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:BL35P02 is a single-chip 8-bit micro-controller |
發布緊急采購，3分鐘左右您將得到回復。