參數資料
型號: BL1062A1
廠商: 上海貝嶺股份有限公司
英文描述: Low voltage transmission circuits with dialer interface
中文描述: 低電壓與撥號器接口傳輸電路
文件頁數: 3/7頁
文件大小: 263K
代理商: BL1062A1
BL1062A1
http://www.belling.com.cn
- 3 -
8/25/2006
Wrote by 2006
Total
7 Pages
Input MUTE
When MUTE is LOW or open-circuit, the DTMF input is enabled and the microphone and
receiving amplifier inputs are inhibited. The reverse is true when MUTE is HIGH. MUTE switching
causes only negligible clicking on the line and earpiece output. If the number of parallel sets in use
causes a drop in line current to below 6 mA the DTMF amplifier becomes active independent to the
DC level applied to the MUTE input.
Dual-tone multi-frequency input DTMF
When the DTMF input is enabled dialling tones may be sent on to the line. The voltage gain
from DTMF to LN is typically 25.5 dB (when R7 = 68 k
) and varies with R7 in the same way as
the microphone gain. The signalling tones can be heard in the earpiece at a low level (confidence
tone).
Receiving amplifier IR, QR and GAR
The receiving amplifier has one input (IR) and a non-inverting output (QR). The IR to QR gain is
typically 31 dB (when R4 = 100 k
). It can be adjusted between 20 and 31 dB to match the
sensitivity of the transducer in use. The gain is set with the value of R4, which is connected
between GAR and QR. The overall receive gain, between LN and QR, is calculated by subtracting
the anti-sidetone network attenuation (32 dB) from the amplifier gain. The output voltage of the
receiving amplifier is specified for continuous-wave drive. The maximum output voltage will be
higher under speech conditions where the peak to RMS ratio is higher.
Automatic Gain Control input AGC
Automatic line loss compensation is achieved by connecting a resistor (R6) between AGC
and V
EE
. The automatic gain control varies the gain of the microphone amplifier and the receiving
amplifier in accordance with the DC line current. The control range is 5.8 dB which corresponds to
a line length of 5 km for a 0.5 mm diameter twisted-pair copper cable with a DC resistance of 176
/km and average attenuation of 1.2 dB/km). Resistor R6 should be chosen in accordance with
the exchange supply voltage and its feeding bridge resistance. The ratio of start and stop currents
of the AGC curve is independent of the value of R6. If no automatic line-loss compensation is
required the AGC pin may be left open-circuit. The amplifiers, in this condition, will give their
maximum specified gain.
Enhanced EMC performance
The input pins BL1062A1 is added RC filters to improve the EMC performance, so the
telephone sets which used BL1062A1 are easily to handle the EMC design.
LIMITING VALUES
SYMBOL
PARAMETER
V
LN
positive continuous line voltage
V
LN(R)
repetitive line voltage during
switch-on or line interruption
V
LN(RM)
repetitive peak line voltage for
a 1 ms pulse per 5 s
see Fig.6
I
line
line current
R9 = 20
P
tot
total power dissipation
R9 = 20
T
amb
operating ambient temperature
T
stg
storage temperature
CONDITIONS
MIN.
MAX.
12
13.2
UNIT
V
V
R9 = 20
; R10 = 13
;
28
V
25
40
140
600
+75
+125
mA
mW
o
C
o
C
相關PDF資料
PDF描述
BL1085 3A LOW DROPOUT LINEAR REGULATOR
BL1085-18CS 3A LOW DROPOUT LINEAR REGULATOR
BL1085-18CS1 3A LOW DROPOUT LINEAR REGULATOR
BL1085-18CY 3A LOW DROPOUT LINEAR REGULATOR
BL1085-18CZ 3A LOW DROPOUT LINEAR REGULATOR
相關代理商/技術參數
參數描述
BL1-08 制造商:FRONTIER 制造商全稱:Frontier Electronics. 功能描述:1A BRIDGE RECTIFIERS
BL1084 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:5A Bipolar Linear Regulator
BL1085 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:3A LOW DROPOUT LINEAR REGULATOR
BL1085-18CS 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:3A LOW DROPOUT LINEAR REGULATOR
BL1085-18CS1 制造商:BELLING 制造商全稱:SHANGHAI BELLING CO., LTD. 功能描述:3A LOW DROPOUT LINEAR REGULATOR