- 您現在的位置：買賣IC網 > PDF目錄369470 > BK5200 Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode PDF資料下載
參數資料
| 型號： | BK5200 |
| 元件分類： | 參考電壓二極管 |
| 英文描述： | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| 中文描述： | 250 的低電流運算，低反向泄露，低噪聲穩壓二極管 |
| 文件頁數： | 10/25頁 |
| 文件大?。?/td> | 1295K |
| 代理商： | BK5200 |
Eiserstrae 5 / D-33415 Verl / Telefon 05246/963-0 / Telefax 05246/963-149
BK5200
Basic information
10
BK5200
The peripheral data in the process image
When the bus coupler is first switched on it determines the configuration of
the attached input/output terminals and automatically assigns the physical
slots of the input/output channels to the addresses in the process image.
The bus coupler sets up an internal list of assignments in which each of the
input and output channels has a specific position in the process image. A
distinction is made here between input and output and between bit-oriented
(digital) and byte-oriented (analog, or complex) signal processing.
It also forms two groups, whereby one contains only inputs and the other
only outputs. In each group, the byte-oriented channels take the lowest
addresses, in ascending order, and these are then followed by the bit-
oriented channels.
Digital signals
(bit-oriented)
Digital signals are bit-oriented. This means that one bit of the process
image is assigned to each digital channel. The bus coupler sets up a block
of memory containing the current input bits and arranges to immediately
write out the bits from a second block of memory which belongs to the out-
put channels.
The precise assignment of the input and output channels to the process
image of the control unit is explained in detail in the Appendix by means of
an example.
Analog signals
(byte-oriented)
The processing of analog signals is always byte-oriented and analog input
and output values are stored in memory in a two-byte representation. The
values are held as ”SIGNED INTEGER” or ”twos-complement”. The digit
”0” represents the input/output value ”0V”, ”0mA” or ”4mA”. When you use
the default settings, the maximum value of the input/output value is given
by ”7FFF” hex. Negative input/output values, such as -10V, are represen-
ted as ”1000” hex and intermediate values are correspondingly proportional
to one another. The full range of 15-bit resolution is not realized at every
input/output level. If you have an actual resolution of 12 bits, the remaining
three bits have no effect on output and are read as ”0” on input. Each
channel also possesses a control and status byte in the highest value byte,
although version 2.0 of the DeveNet coupler does not permit the control
and status byte to be read. An analog channel is represented by 2 bytes in
the process image.
Special signals and
interface
A bus coupler supports bus terminals with additional interfaces, such as
RS232, RS485, incremental encoder, etc.. These signals can be regarded
in the same way as the analog signals described above. A 16-bit data
width may not be sufficient for all such special signals; the bus coupler can
support any data width.
Default assignment of
inputs and outputs to the
process image
When the bus coupler is first switched on it determines the number of atta-
ched bus terminals and sets up a list of assignments. This list distinguishes
between analog channels and digital channels and between input and out-
put; which are grouped separately. The assignments begin immediately to
the left of the bus coupler. The software in the bus coupler creates the
assignment list by collecting the entries for the individual channels one at a
time, counting from left to right. These assignments distinguish four groups:
Function type of the channel
Analog outputs
Digital outputs
Analog inputs
Digital inputs
Assignment level
byte-wise assignment
bit-wise assignment
byte-wise assignment
bit-wise assignment
1.
2.
3.
4
相關PDF資料 |
PDF描述 |
|---|---|
| BK60A-048L-050F30G | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| BK60A-048L-120F13G | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| BK60A-048L-150F10 | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| BK60A-300L-050F30G | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
| BK60A-300L-120F13G | Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BK-53 | 制造商:Memory Protection Devices Inc (MPD) 功能描述:BATTERY CLIP AA |
| BK-53-TR | 功能描述:CLIP CONTACT BATTERY AA SMD RoHS:是 類別:電池產品 >> 電池座，夾，觸點 系列:- 標準包裝:100 系列:- 電池類型，功能:圓柱形，觸點（單） 樣式:觸點彈簧（線圈） 電池大小:多重 單元數:- 電池系列:- 安裝類型:自定義 端接類型:- 板上方高度:- 工作溫度:- 配用:P670-ND - BATTERY 1.5V ALKALINE AAA 4 PACKP671-ND - BATTERY 1.5V ALKALINE AA 4 PACKP672-ND - BATTERY 1.5V ALKALINE AAA 2 PACKP673-ND - BATTERY 1.5V ALKALINE AA 2 PACKP674-ND - BATTERY 1.5V ALKALINE AAAP675-ND - BATTERY 1.5V ALKALINE AATL-4903-ND - BATT LTH AA 3.6VLR03XWA/C-ND - BATT IND ALKALINE AAA SIZELR6XWA/C-ND - BATT IND ALKALINE AA SIZEP649-ND - BATTERY IND ALKALINE AAA更多... 其它名稱:211K |
| BK5491A | 制造商:B&K Precision Corporation 功能描述:MULTIMETER BENCH 50000 COUNT |
| BK5491B | 制造商:B&K Precision Corporation 功能描述:MULTIMETER, BENCH DUAL DISPLAY 50000 |
| BK5492 | 制造商:B&K Precision Corporation 功能描述:MULTIMETER BENCH 120000 COUNT |
發布緊急采購，3分鐘左右您將得到回復。