- 您現在的位置：買賣IC網 > PDF目錄376497 > BGY1816S (NXP SEMICONDUCTORS) UHF amplifier module PDF資料下載
參數資料
| 型號： | BGY1816S |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 衰減器 |
| 英文描述： | UHF amplifier module |
| 中文描述： | 1805 MHz - 1880 MHz RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| 封裝： | PLASTIC, SOT501A, 4 PIN |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 68K |
| 代理商： | BGY1816S |
1999 Apr 13
6
Philips Semiconductors
Product specification
UHF amplifier module
BGY1816S
MOUNTING RECOMMENDATIONS
To ensure a good thermal contact and to prevent
mechanical stress when bolted down, the flatness of the
mounting base is designed to be typically better than
0.1 mm. The mounting area of the heatsink should be flat
and free from burrs and loose particles. The heatsink
should be rigid and not prone to bowing under thermal
cycling conditions. The thickness of a solid heatsink
should be not less than 5 mm to ensure a rigid assembly.
A thin, even layer of thermal compound should be applied
between the mounting base and the heatsink to achieve
the best possible thermal contact resistance. Excessive
use of thermal compound will result in an increase in
thermal resistance and possible bowing of the mounting
base; too little will also result in poor thermal conduction.
The module should be mounted to the heatsink using
3 mm bolts with flat washers. The bolts should first be
tightened to “finger tight” and then further tightened in
alternating steps to a maximum torque of 0.4 to 0.6 Nm.
Once mounted on the heatsink, the module leads can be
soldered to the printed-circuit board. A soldering iron may
be used up to a temperature of 250
°
C for a maximum of
10 seconds at a distance of 2 mm from the plastic cap.
ESD precautions must be taken to protect the device from
electrostatic damage.
相關PDF資料 |
PDF描述 |
|---|---|
| BGY1816 | UHF amplifier module |
| BGY212 | UHF amplifier module |
| BGY212A | UHF amplifier module |
| BGY241 | UHF amplifier module |
| BLF1820-90 | UHF power LDMOS transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BGY1916 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:UHF amplifier module |
| BGY200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RF Amplifier |
| BGY2016 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:UHF amplifier module |
| BGY2016,127 | 功能描述:射頻放大器 RAIL TNS-RFPR RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| BGY204 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:UHF amplifier module |
發布緊急采購，3分鐘左右您將得到回復。