- 您現在的位置：買賣IC網 > PDF目錄166429 > BD6231HFP BRUSH DC MOTOR CONTROLLER, 1 A, PSSO8 PDF資料下載
參數資料
| 型號： | BD6231HFP |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 1 A, PSSO8 |
| 封裝： | HRP-7 |
| 文件頁數： | 2/17頁 |
| 文件大?。?/td> | 713K |
| 代理商： | BD6231HFP |
10/16
e) f) PWM control mode
The rotational speed of the motor can be controlled by the switching duty when the PWM signal is input to the FIN
pin or the RIN pin. In this mode, the high side output is fixed and the low side output does the switching,
corresponding to the input signal. The switching operates by the output state toggling between "L" and "Hi-Z".
The PWM frequency can be input in the range between 20kHz and 100kHz. Note that control may not be attained
by switching on duty at frequencies lower than 20kHz, since the operation functions via the stand-by mode. Also,
circuit operation may not respond correctly when the input signal is higher than 100kHz. To operate in this mode,
connect the VREF pin with VCC pin. In addition, establish a current path for the recovery current from the motor, by
connecting a bypass capacitor (10μF or more is recommended) between VCC and ground.
Control input : H
Control input : L
Fig.39 PWM control operation (output stage)
Fig.40 PWM control operation (timing chart)
g) h) VREF control mode
The built-in VREF-switching on duty conversion circuit provides switching duty corresponding to the voltage of the
VREF pin and the VCC voltage. The function offers the same level of control as the high voltage output setting
function in previous models. The on duty is shown by the following equation.
DUTY VREF [V] / VCC [V]
For example, if VCC voltage is 24V and VREF pin voltage is 18V, the switching on duty is about 75 percent.
However, please note that the switching on duty might be limited by the range of VREF pin voltage (Refer to the
operating conditions, shown on page 2). The PWM carrier frequency in this mode is 25kHz (nominal), and the
switching operation is the same as it is the PWM control modes. When operating in this mode, do not input the
PWM signal to the FIN and RIN pins. In addition, establish a current path for the recovery current from the motor,
by connecting a bypass capacitor (10μF or more is recommended) between VCC and ground.
Fig.41 VREF control operation (timing chart)
M
ON
OFF
ON
M
ON
OFF
VCC
VREF
FIN
RIN
OUT1
OUT2
0
FIN
RIN
OUT1
OUT2
相關PDF資料 |
PDF描述 |
|---|---|
| BD6718FV-E2 | BRUSHLESS DC MOTOR CONTROLLER, 0.02 A, PDSO20 |
| BD9007HFP | 2 A SWITCHING REGULATOR, 505 kHz SWITCHING FREQ-MAX, PSSO7 |
| BD9831AMWV | SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PQCC56 |
| BD9870FPS | 1.5 A SWITCHING REGULATOR, 990 kHz SWITCHING FREQ-MAX, PSSO4 |
| BDC-062BNX-014 | 62.5/125 um, MULTI MODE, DUPLEX FIBER OPTIC CONNECTOR, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BD6231HFP-TR | 功能描述:馬達/運動/點火控制器和驅動器 H-BRIDGE 36V max 1 Chan 1.0A 1.5ohm RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| BD6232 | 制造商:ROHM 制造商全稱:Rohm 功能描述:H-bridge drivers (36V max.) |
| BD62321HFP | 制造商:ROHM 制造商全稱:Rohm 功能描述:H-bridge driver |
| BD62321HFP-TR | 功能描述:IC H-BRIDGE DVR 36V 1CH 3A HRP7 RoHS:是 類別:集成電路 (IC) >> PMIC - 電機和風扇控制器，驅動器 系列:- 標準包裝:1 系列:- 應用:直流電機驅動器，步進電機驅動器 評估套件:- 輸出數:1 或 2 電流 - 輸出:750mA 電壓 - 負載:10 V ~ 40 V 電源電壓:4.5 V ~ 5.5 V 工作溫度:-20°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-BFSOP（0.295"，7.50mm 寬） 供應商設備封裝:24-SOP 包裝:Digi-Reel® 其它名稱:MTS62C19A-HS105DKR |
| BD6232FP | 制造商:ROHM 制造商全稱:Rohm 功能描述:H-Bridge Motor Drivers For DC Brush Motors |
發布緊急采購，3分鐘左右您將得到回復。