- 您現在的位置：買賣IC網 > PDF目錄166429 > BD4723G 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 PDF資料下載
參數資料
| 型號： | BD4723G |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封裝： | ROHS COMPLIANT, SSOP-5 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 282K |
| 代理商： | BD4723G |
Technical Note
6/7
BD47□□G series
www.rohm.com
2010.01 - Rev.B
2010 ROHM Co., Ltd. All rights reserved.
Operation Notes
1.
Absolute maximum range
Absolute Maximum Ratings are those values beyond which the life of a device may be destroyed. We cannot be defined the
failure mode, such as short mode or open mode. Therefore a physical security countermeasure, like fuse, is to be given
when a specific mode to be beyond absolute maximum ratings is considered.
2.
GND potential
GND terminal should be a lowest voltage potential every state. Please make sure all pins, which are over ground even if,
include transient feature.
3.
Electromagnetic Field
Mal-function may happen when the device is used in the strong electromagnetic field.
4.
Bypass Capacitor for Noise Rejection
Please put into the capacitor between VCC pin and GND, to reject noise. If extremely big capacitor is used, transient
response might be late. Please confirm sufficiently for the point.
5.
Short Circuit between Terminal and Soldering
Don’t short-circuit between Output pin and VCC pin, Output pin and GND pin, or VCC pin and GND pin. When soldering the
IC on circuit board, please be unusually cautious about the orientation and the position of the IC. When the orientation is
mistaken the IC may be destroyed.
6.
This IC has extremely high impedance terminals. Small leak current due to the uncleanness of PCB surface might cause
unexpected operations. Application values in these conditions should be selected carefully. If the leakage is assumed
between the VOUT terminal and the GND terminal, the pull-up resistor should be less than 1/10 of the assumed leak
resistance.
7. External parameters
The recommended parameter range for RL is 2k~1M. There are many factors (board layout, etc) that can affect
characteristics. Please verify and confirm using practical applications.
8.
Power on reset operation
Please note that the power on reset output varies with the VDD rise up time. Please verify the actual operation.
9.
Precautions for board inspection
Connecting low-impedance capacitors to run inspections with the board may produce stress on the IC. Therefore, be
certain to use proper discharge procedure before each process of the test operation.
To prevent electrostatic accumulation and discharge in the assembly process, thoroughly ground yourself and any
equipment that could sustain ESD damage, and continue observing ESD-prevention procedures in all handing, transfer
and storage operations. Before attempting to connect components to the test setup, make certain that the power supply is
OFF. Likewise, be sure the power supply is OFF before removing any component connected to the test setup.
10. When the power supply, is turned on because of in certain cases, momentary Rash-current flow into the IC at the logic
unsettled, the couple capacitance, GND pattern of width and leading line must be considered.
相關PDF資料 |
PDF描述 |
|---|---|
| BD5338FVE | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| BD6066EKN | Step-up DC/DC converter for middle size LCD panel |
| BD6066GU | Step-up DC/DC converter for middle size LCD panel |
| BD6068GUT | Synchronous rectification Step-up DC/DC converter for middle phone |
| BD6231HFP | BRUSH DC MOTOR CONTROLLER, 1 A, PSSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BD4723G-TR | 功能描述:電壓監測器/監控器 RESET DETEC VOLT 2.3V RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| BD4724 | 制造商:ROHM 制造商全稱:Rohm 功能描述:Bipolar Voltage Detector IC |
| BD4724G | 制造商:ROHM 制造商全稱:Rohm 功能描述:System Reset IC |
| BD4724G-TR | 功能描述:電壓監測器/監控器 RESET DETEC VOLT 2.4V RoHS:否 制造商:Texas Instruments 監測電壓數:2 監測電壓:Adjustable 輸出類型:Open Drain 欠電壓閾值: 過電壓閾值: 準確性:1 % 工作電源電壓:1.5 V to 6.5 V 工作電源電流:1.8 uA 最大工作溫度:+ 125 C 封裝 / 箱體:SON-6 安裝風格:SMD/SMT |
| BD4725 | 制造商:ROHM 制造商全稱:Rohm 功能描述:RESET IC |
發布緊急采購，3分鐘左右您將得到回復。