- 您現在的位置：買賣IC網 > PDF目錄384111 > BA07TFP (Rohm CO.,LTD.) Low saturation voltage type 3-pin regulator PDF資料下載
參數資料
| 型號： | BA07TFP |
| 廠商： | Rohm CO.,LTD. |
| 英文描述： | Low saturation voltage type 3-pin regulator |
| 中文描述： | 低飽和電壓型3針調節器 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 100K |
| 代理商： | BA07TFP |
BAOOT / FP series
Regulator ICs
!
Operation notes
(1) Operating power supply voltage
When operating within the normal voltage range and
within the ambient operating temperature range, most
circuit functions are guaranteed.
The rated values cannot be guaranteed for the electrical
characteristics, but there are no sudden changes of the
characteristics within these ranges.
(2) Power dissipation
Heat attenuation characteristics are noted on a separate
page and can be used as a guide in judging power
dissipation.
If these ICs are used in such a way that the allowable
power dissipation level is exceeded, an increase in the
chip temperature could cause a reduction in the current
capability or could otherwise adversely affect the
performance of the IC. Make sure a sufficient margin is
allowed so that the allowable power dissipation value is
not exceeded.
(3) Output oscillation prevention and bypass capacitor
Be sure to connect a capacitor between the output pin
and GND to prevent oscillation. Since fluctuations in the
valve of the capacitor due to temperature changes may
cause oscillations, a tantalum electrolytic capacitor with a
small internal series resistance (ESR) is recommended.
A 22
μ
F capacitor is recommended; however, be aware
that if an extremely large capacitance is used (1000
μ
F
or greater), then oscillations may occur at low
frequencies. Therefore, be sure to perform the
appropriate verifications before selecting the capacitor.
Also, we recommend connecting a 0.33
μ
F bypass
capacitor as close as possible between the input pin and
GND.
(4) Overcurrent protection circuit
An overcurrent protection circuit is built into the outputs,
to prevent destruction of the IC in the even the load is
shorted.
This protection circuit limits the current in the shape of
a ’7’. This circuit is designed with a high margin, so that
that current is restricted and latching is prevented, even if
a high-capacitance capacitator causes a large amount of
current to temporary flow through the IC.
However, these protection circuits are only good for pre-
venting damage from sudden accidents and should not
be used for continuous protection (for instance, clamping
at an output of 1V
F
or greater; below 1V
F
, the short mode
circuit operates). Note that the capacitor has negative
temperature characteristics, and the design should take
this into consideration.
(5) Thermal overload circuit
A built-in thermal overload circuit prevents damage from
overheating. When the thermal circuit is activated, the
outputs are turned OFF. When the temperature drops
back to a constant level, the circuit is restored.
(6) Internal circuits could be damaged if there are
modes in which the electric potential of the application’s
input (V
CC
) and GND are the opposite of the electric
potential normally used by each of the outputs. Use of a
diode or other such bypass path is recommended.
(7) Although the manufacture of this product includes
rigorous quality assurance procedures, the product may
be damaged if absolute maximum ratings for voltage or
operating temperature are exceeded. If damage has
occurred, special modes (such as short circuit mode or
open circuit mode) cannot be specified. If it is possible
that such special modes may be needed, please
consider using a fuse or some other mechanical safety
mea-sure.
(8) When used within a strong magnetic field, be aware
that the possibility of malfunction exists.
相關PDF資料 |
PDF描述 |
|---|---|
| BA1282-TR | Band Switching Diodes |
| BA1282-TR3 | Band Switching Diodes |
| BA1283-TR | Band Switching Diodes |
| BA1283-TR3 | Band Switching Diodes |
| BA1282 | Silicon Planar Diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BA08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| BA-080808-FMM-TL001 | 功能描述:STANDARD 制造商:amphenol ltw 系列:* 零件狀態:在售 標準包裝:10 |
| BA08CC0FP | 制造商:ROHM 制造商全稱:Rohm 功能描述:1A Low Dropout Voltage Regulator (Adjustable Voltage) |
| BA08CC0FP-E2 | 功能描述:低壓差穩壓器 - LDO REG 1A 8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| BA08CC0T | 功能描述:低壓差穩壓器 - LDO REG 1A 8V RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。