- 您現(xiàn)在的位置：買賣IC網 > PDF目錄385105 > B41821A3108M001 (EPCOS AG) Single-ended capacitors PDF資料下載
參數資料
| 型號： | B41821A3108M001 |
| 廠商： | EPCOS AG |
| 英文描述： | Single-ended capacitors |
| 中文描述： | 單端電容器 |
| 文件頁數： | 34/36頁 |
| 文件大?。?/td> | 809K |
| 代理商： | B41821A3108M001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
Polarity
Make sure that polar capacitors are connected
with the right polarity.
Reverse voltage
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Upper category
temperature
Maintenance
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
Mounting
position of screw
terminal capacitors
11.1.
"Mounting positions of
capacitors with screw
terminals"
11.4
"Mounting
considerations for
single-ended capacitors"
Mounting of
single-ended
capacitors
The internal structure of single-ended capacitors
might be damaged if excessive force is applied to
the lead wires.
Avoid any compressive, tensile or flexural stress.
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
not be exceeded when connecting screw
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature
limits during soldering.
Robustness of
terminals
11.3
"Mounting torques"
Soldering
11.5
"Soldering"
B41821, B43821
Standard series
85
°
C
Page 34 of 36
Pleaseread
Cautionsandwarnings
and
Importantnotes
attheendofthisdocument.
相關PDF資料 |
PDF描述 |
|---|---|
| B43304B2188M000 | Snap-In Capacitors |
| B43501A3227M007 | Snap-In Capacitors Long Useful Life - 85 |
| B43501A3477M000 | Snap-In Capacitors Long Useful Life - 85 |
| B43501B2227M002 | Snap-In Capacitors Long Useful Life - 85 |
| B43693A2686Q007 | Axial-lead and Soldering Star Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| B41821A3108M002 | 功能描述:鋁質電解電容器 - 帶引線 AL-ELKO 1000UF 10V SINGLE ENDED RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk |
| B41821A3108M003 | 制造商:EPCOS 制造商全稱:EPCOS 功能描述:Single-ended capacitors |
| B41821A3108M008 | 功能描述:鋁質電解電容器 - 帶引線 AL-ELKO 1000UF 10V SINGLE ENDED RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk |
| B41821A3108M2 | 功能描述:鋁質電解電容器 - 帶引線 AL-ELKO SINGLE ENDED 1000UF 10V RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk |
| B41821A3108M8 | 功能描述:鋁質電解電容器 - 帶引線 AL-ELKO SINGLE ENDED 1000UF 10V RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。