- 您現在的位置：買賣IC網 > PDF目錄92940 > AWT910S6C (ANADIGICS INC) RF/MICROWAVE WIDE BAND HIGH POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | AWT910S6C |
| 廠商： | ANADIGICS INC |
| 元件分類： | 放大器 |
| 英文描述： | RF/MICROWAVE WIDE BAND HIGH POWER AMPLIFIER |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 50K |
| 代理商： | AWT910S6C |
AWT910S6C
23/04/98
3
35 Technology Drive Warren NJ 07059 *Phone (908)668 5000 * Fax (908) 668 5132
Email: mktg@anadigics.com
PIN
SIGNAL
DESCRIPTION
1
GND
RF and DC Ground
2RFIN
RF power input, DC blocked
3VREF
Output Power control, Should be
set to level that corresponds to
the desired output power. Pulse
control voltage (VREF, 0 to 3 V)
4VDB
Bias circuit Supply (+ 6.0V)
5VSS_IN
Negative Supply (- 4V) generated
by the dc/dc converter
6,7,8,9
GND
RF and DC Ground
10
VSS_OUT
The output of the dc/dc converter
providing the negative voltage
11,12
Pump capacitor (C5), which is
part of the dc/dc converter circuit.
13
VGEN
DC/DC converter positive supply
14
VGENGND
AC and DC ground for the dc/dc
converter .If possible should be
grounded through a separate via
hole.
15
GND
RF and DC ground.
16
VD2
The open drain of the second
amplifier stage
17
GND
RF and DC Ground
18
N/C
Not Connected
19
VD3B
3
rd stage drain supply (6.0 V) and
RFOUT
20,21,22,23
GND
RF and DC ground
24
VD3A
3rd stage drain supply (6.0 V)
and RFOUT
25
N/C
Not Connected
26
GND
RF and DC ground
27
VD1
1
st stage drain supply (6.0 V)
28
GND
RF and DC Ground
4. Recommended Operating Procedure on the Evaluation Board
Power Up
A. Begin by setting all power supplies to zero volts,
B. Make sure that the input RF power is turned off.
C. Turn on VGEN (Pin 13) to + 4.8 V
D. Check the voltage @ VSSIN (pin 5) to see if it is between - 4.8 V and – 3V, if voltage is
not, check the pin alignment.
E. Turn on VD1 (Pin 27), VD2 (Pin 16), VD3 (Pins 19 and 24) and VDB (Pin 4) which are tied
together on the fixture, and set to +6.0 V. Little drain current should be flowing at this
time (IDD< 5 mA).
F. Turn RF on and adjust input power to 5 dBm.
G. Turn VREF on. Adjust VREF to desired output power (< = 33.0 dBm).
Power Down
To power down the device follow the above procedure in reverse order .
相關PDF資料 |
PDF描述 |
|---|---|
| AWT920S12 | RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AWT920 | RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AWT924S10 | RF/MICROWAVE NARROW BAND HIGH POWER AMPLIFIER |
| AWT937 | RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| AWU6616P9 | 824 MHz - 849 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AWT921 | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:900MHz Integrated Power Amp |
| AWT921S11 | 制造商:ANADIGICS 制造商全稱:ANADIGICS, Inc 功能描述:Integrated High Power Amp 900 MHz |
| AWTA1504 | 功能描述:撥動開關 SPST ON-OFF 20A PNL PWR TOGGLE RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated |
| AWTD1504 | 功能描述:撥動開關 SPDT ON-ON BAT 20A PWR TOGGLE SWTCH RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated |
| AWTE1504 | 功能描述:撥動開關 SPDT ON-OFF-ON BAT 20A PWR TOGGLE SWTCH RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated |
發布緊急采購，3分鐘左右您將得到回復。