參數資料
型號： ATSAM3N4CA-CU
廠商： Atmel
文件頁數： 19/60頁
文件大?。?/td> 0K
描述： MCU FLASH 100-BGA
產品培訓模塊： Touch Solutions on the Atmel ARM? Cortex?-M3 Based Flash Microcontrollers
特色產品： SAM3N Flash MCU
標準包裝： 260
系列： SAM3N
核心處理器： ARM? Cortex?-M3
芯體尺寸： 32-位
速度： 48MHz
連通性： I²C，IrDA，SPI，UART/USART
外圍設備： 欠壓檢測/復位，DMA，POR，PWM，WDT
輸入/輸出數： 79
程序存儲器容量： 256KB（256K x 8）
程序存儲器類型： 閃存
RAM 容量： 24K x 8
電壓 - 電源 (Vcc/Vdd)： 1.62 V ~ 3.6 V
數據轉換器： A/D 16x10b; D/A 1x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-TFBGA
包裝： 托盤
26
11011BS–ATARM–22-Feb-12
SAM3N Summary
6.3
Test Pin
The TST pin is used for JTAG Boundary Scan Manufacturing Test or Fast Flash programming
mode of the SAM3N series. The TST pin integrates a permanent pull-down resistor of about 15
k
Ω to GND, so that it can be left unconnected for normal operations. To enter fast programming
mode, see the Fast Flash Programming Interface (FFPI) section. For more on the manufacturing
and test mode, refer to the “Debug and Test” section of the product datasheet.
6.4
NRST Pin
The NRST pin is bidirectional. It is handled by the on-chip reset controller and can be driven low
to provide a reset signal to the external components or asserted low externally to reset the
microcontroller. It will reset the Core and the peripherals except the Backup region (RTC, RTT
and Supply Controller). There is no constraint on the length of the reset pulse and the reset con-
troller can guarantee a minimum pulse length. The NRST pin integrates a permanent pull-up
resistor to VDDIO of about 100 k
Ω . By default, the NRST pin is configured as an input.
6.5
ERASE Pin
The ERASE pin is used to reinitialize the Flash content (and some of its NVM bits) to an erased
state (all bits read as logic level 1). It integrates a pull-down resistor of about 100 k
Ω to GND, so
that it can be left unconnected for normal operations.
This pin is debounced by SCLK to improve the glitch tolerance. When the ERASE pin is tied high
during less than 100 ms, it is not taken into account. The pin must be tied high during more than
220 ms to perform a Flash erase operation.
The ERASE pin is a system I/O pin and can be used as a standard I/O. At startup, the ERASE
pin is not configured as a PIO pin. If the ERASE pin is used as a standard I/O, startup level of
this pin must be low to prevent unwanted erasing. Please refer to Section 11.2 “Peripheral Sig-
nals Multiplexing on I/O Lines” on page 42. Also, if the ERASE pin is used as a standard I/O
output, asserting the pin to low does not erase the Flash.
相關PDF資料
PDF描述
VJ1812Y333JXPAT5Z CAP CER 0.033UF 250V 5% X7R 1812
3840-100 BNC MALE TERM PLUG 100 OHMS
VE-J0N-IY-F2 CONVERTER MOD DC/DC 18.5V 50W
ATMEGA32M1-AU MPU AVR 32K FLASH 20MHZ 32TQFP
VE-J0N-IY-F1 CONVERTER MOD DC/DC 18.5V 50W
相關代理商/技術參數
參數描述
ATSAM3N-EK 功能描述:開發板和工具包 - ARM EVAL KIT SAM3N RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
ATSAM3S 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Cortex M3-based Processor
ATSAM3S1AA-AU 功能描述:ARM微控制器 - MCU MRL A 64K Flash 16K SRAM Ind Temp RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
ATSAM3S1AA-AUR 制造商:Atmel Corporation 功能描述:LQFP,GREEN,IND TEMP,MRL A,T&R - Tape and Reel 制造商:Atmel Corporation 功能描述:IC MCU 32BIT FLASH 48LQFP 制造商:Atmel Corporation 功能描述:ARM Microcontrollers - MCU LQFPGREENIND TEMPMRL A
ATSAM3S1AA-MU 功能描述:ARM微控制器 - MCU MRL A 64K Flash 16K SRAM Ind Temp RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*