- 您現在的位置：買賣IC網 > PDF目錄375377 > ATS643LSH-I2 (Allegro MicroSystems, Inc.) Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update PDF資料下載
參數資料
| 型號： | ATS643LSH-I2 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| 中文描述： | 自校準，零的高速連續更新差動齒輪齒傳感器 |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 501K |
| 代理商： | ATS643LSH-I2 |
12
ATS643-DS, Rev. 1
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Self-Calibrating, Zero-Speed Differential GTS with Continuous Update
ATS643LSH
Start Mode Hysteresis
. This feature helps to ensure optimal
self-calibration by rejecting electrical noise and low-amplitude
target vibration during initialization. This prevents AGC from
calibrating the sensor on such spurious signals. Calibration can
be performed using the actual target features.
A typical scenario is shown in figure 6. The hysteresis, PO
HYS
,
is a minimum level of the peak-to-peak amplitude of the internal
analog electrical signal, V
PROC
, that must be exceeded before the
ATS643 starts to compute switchpoints.
Figure 6. Operation of Start Mode Hysteresis
Position 1. At power-on, the ATS643 begins sampling V
PROC
.
Position 2. At the point where the Start Mode Hysteresis is exceeded, the device begins to establish switching thresholds (B
OP
and B
RP
) using the Con-
tinuous Update algorithm. After this point, Start Mode Hysteresis is no longer a consideration. Note that a valid V
PROC
value exceeding the Start Mode
Hysteresis can be generated either by a legitimate target feature or by excessive vibration.
Position 3. In this example, the first switchpoint transition is through B
OP
. and the output transitions from high to low.
If the first switchpoint transition had been through B
RP
(such as position 4), no output transition would occur because I
OUT
already would be in the high
polarity. The first transition would occur at position 5 (B
OP
).
B
RP(#1)
B
OP(#1)
B
OP(#2)
1
3
4
5
5
2
1
2
Start Mode Hysteresis, PO
HYS
Output Signal, I
OUT
Sensor Position Relative to Target
Target Magnetic Profile
Differential Signal, V
PROC
Target, Gear
相關PDF資料 |
PDF描述 |
|---|---|
| ATS643LSH | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS643LSH-I1 | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS643LSHTN-I1-T | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS643LSHTN-I2-T | Self-Calibrating, Zero-Speed Differential Gear Tooth Sensor with Continuous Update |
| ATS645LSHTN-I1-T | True Zero Speed Miniature Gear Tooth Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS643LSHTN-I1-T | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS643LSHTN-I2-T | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS645 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:True Zero Speed Miniature Gear-Tooth Sensor |
| ATS645LSH | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:True Zero Speed Miniature Gear Tooth Sensor |
| ATS645LSH-I2 | 制造商:Allegro MicroSystems LLC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。