參數資料
型號: ATS636LSE
廠商: Allegro MicroSystems, Inc.
英文描述: Programmable Back Biased Hall-Effect Switch with TPOS Functionality
中文描述: 可編程回到偏霍爾效應的聚烯烴功能開關
文件頁數: 7/15頁
文件大小: 814K
代理商: ATS636LSE
ATS635LSE and ATS636LSE
PROGRAMMABLE TRUE POWER-ON HALL-EFFECT GEAR-TOOTH SWITCHES
Page 7 of 15
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright 200
5
Allegro MicroSystems, Inc.
FUNCTION DESCRIPTION: ADDRESSING / PROGRAMMING PROTOCOL
The ATS635LSE and ATS636LSE magnetic operate point (B
OP
) is programmed by serially addressing the devices
through the supply terminal (1). After the correct operate point is determined, the device programming bits are selected
and blown, then a lock bit is selected and blown to prevent any further (accidental) programming.
Addressing:
Bop is programmable in both the positive and negative direction from its initial value. Addressing is used to
determine the desired code, while programming is used to lock the code. A unique key is needed to blow fuses, while
addressing as described below does not allow for the device to be programmed accidentally.
Addressing with positive polarity.
The magnetic operate point (B
OP
) is adjustable using 7 bits or 128 addresses. The
Addresses are sequentially selected (Figure 2) until the required operate point is reached. The first address must be
selected with a High voltage pulse (V
PP
), while the remaining pulses should be V
PH
Pulses. Note that the difference
between B
OP
and the magnetic release point (B
RP
), the Hysteresis (B
HYS
), is fixed for all addresses.
0
V
PL
V
PH
t
d(1)
t
d(0)
C
C
C
C
C
C
(
V
PP
Figure 2 – Addressing Pulses: Positive Polarity
Addressing with negative polarity.
The magnetic operate point (B
OP
) is adjustable with negative polarity using 7 bits or
128 addresses. To invert the polarity it is necessary to first apply a keying sequence (Figure 3). The polarity key contains
a V
PP
pulse and at least 1 V
PH
pulse, but no more than 6 V
PH
pulses; the key in Figure 3 shows 2 V
PH
pulses. The
addresses are then sequentially selected until the required operate point is reached. The first address must be selected
with a High voltage pulse (V
PP
), while the remaining pulses should be V
PH
Pulses.
0
V
PP
V
PL
V
PH
t
d(1)
t
d(0)
C
C
C
C
C
C
(
P
K
Figure 3 – Addressing Pulses: Negative Polarity
相關PDF資料
PDF描述
ATS635LSE Programmable Back Biased Hall-Effect Switch with TPOS Functionality
ATS635LSETN-T Programmable Back Biased Hall-Effect Switch with TPOS Functionality
ATS636LSETN-T RESISTOR, FIXED, FILM, CHIP
ATS640JSB True Zero-Speed,Self-Calibrating ,Hall-Effect Gear-Tooth Sensor For Two-Wire Applications(真速度歸零,自校準,霍爾效應齒輪嚙合傳感器(用于2線))
ATS642LSH Two-Wire True Zero Speed Miniature Differential Peak-Detecting Gear Tooth Sensor with Continuous Calibration
相關代理商/技術參數
參數描述
ATS636LSE_12 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:The ATS636LSE programmable, true power-on state (TPOS), device is optimized Hall-effect IC and rare-earth pellet combinations that switch in response to magnetic signals...
ATS636LSETN 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:否 類別:傳感器,轉換器 >> 磁性 - 霍爾效應,數字式開關,線性,羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出(最大):- 輸出類型:數字式,PWM,8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP(0.209",5.30mm 寬) 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR
ATS636LSETN-T 功能描述:IC HALL EFFECT SWITCH TPOS 4-SIP RoHS:是 類別:傳感器,轉換器 >> 磁性 - 霍爾效應,數字式開關,線性,羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出(最大):- 輸出類型:數字式,PWM,8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP(0.209",5.30mm 寬) 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR
ATS-638194300 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:Hand Crimp Tool for Wire-to-Board Terminal, 28-30 AWG Wire for Loose Parts Only
ATS-638194400 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:A full cycle ratcheting hand tool ensures complete crimps