參數資料
型號： ATS627LSGTN-T
廠商： Allegro Microsystems Inc
文件頁數： 4/22頁
文件大?。?/td> 498K
描述： IC HALL EFFECT GEAR SENSOR 4-SIP
特色產品： ATS627 Position Sensor IC
標準包裝： 1
傳感范圍： 3mT ~ 120mT
類型： 專用型
電源電壓： 4 V ~ 24 V
電流 - 電源： 12mA
電流 - 輸出（最大）： 25mA
輸出類型： 數字，開路集電極
特點： 輪齒類型
工作溫度： -40°C ~ 150°C
封裝/外殼： 4-SIP
供應商設備封裝： 4-SIP
包裝： 標準包裝
其它名稱： 620-1398-6
True Zero Speed, Low Jitter, High Accuracy
 Position Sensor IC
ATS627LSG
4
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Relative Timing Accuracy, Sequential
Mechanical Falling Edges
ERR
FF
 
0.5 mm d AG d 2.5 mm; constant target speed,
Running mode; relative to measurement taken
at AG = 1.5 mm


?.4     deg.
Relative Timing Accuracy, Signature
Mechanical Rising Edge
ERR
SIGR
 
0.5 mm d AG d 2.5 mm; constant target speed,
Running mode; relative to measurement taken
at AG = 1.5 mm


?.4     deg.
Relative Timing Accuracy, Signature
Mechanical Falling Edge
ERR
SIGF
0.5 mm d AG d 2.5 mm; constant target speed,
Running mode; relative to measurement taken
at AG = 1.5 mm


?.5     deg.
Relative Repeatability, Sequential
Rising and Falling Edges
6
T
楨
   0.5 mm d AG d 2.5 mm


0.08     deg.
Output Propagation Delay
t
d(OUT)
See figure 1

20

約
Initial Edge Accuracy
7
 
Edge Accuracy  First and Second
Output Edges
See figure 2
T
TARGET
        T
TARGET
    deg.
Edge Accuracy  Third through Sixth
Output Edges
See figure 2
0.5 x
T
TARGET
 

+0.5 x
T
TARGET
 
deg.
Full Edge Accuracy
Output edge count (see figure 2),
B
SIG
 / B
SEQ
 = 1, or no signature tooth encountered


6

Output edge count (see figure 2), signature
region encountered during calibration, and
B
SIG
 / B
SEQ
 ` 1

9


 Input Magnetic Characteristics 
Allowable Differential Sequential
Signal Variation
8
 
B
SEQ(min)
 /
B
SEQ(max)
 
Total variation over 60 cycles (see figure 3)
0.5



B
SEQ(n+1)
 /
B
SEQ(n)
Single cycle-to-cycle variation (see figure 3)
0.6



Allowable Signature Amplitude Ratio
B
SIG
 /
B
SEQ
 
One instance per target revolution (see figure 3)    0.8

1.6

1
Typical values are at T
A
 = 25癈 and V
CC
 = 12 V.
2
Maximum voltage must be adjusted for power dissipation and junction temperature; see Power Derating section.
3
Negative current is defined as current coming out of (sourced from) the specified device terminal.
4
Sustained voltages beyond the clamp voltage may cause permanent damage to the IC.
5
1 G (gauss) = 0.1 mT (millitesla).
6
The repeatability specification is based on statistical evaluation of a sample population, evaluated at 1000 Hz.
7
Power-on frequencies d 200 Hz. Higher power-on frequencies may result in a delay of full output accuracy or undetected target edges.
8
Excludes effects caused by signature region.
OPERATING CHARACTERISTICS (continued) Valid through full operating supply voltage and ambient temperature ranges, using 
Reference Target 60+2; unless otherwise specified
Characteristics
Symbol
Test Conditions
Min.    Typ.
1
Max.    Unit
Performance Characteristics (continued) 
相關PDF資料
PDF描述
ATS635LSETN-T IC SENSOR GEAR TOOTH 4-SIP
ATS643LSHTN-I2-T IC SENSOR GEAR TOOTH 4-SIP
ATS645LSHTN-I1 IC SENSOR GEAR TOOTH 4-SIP
ATS667LSGTN-T IC SENSOR GEAR TOOTH 4SIP
ATS674LSETN-LT-T IC SENSOR GEAR TOOTH 4-SIP
相關代理商/技術參數
參數描述
ATS630LSA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
ATS630LSB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
ATS631LSA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
ATS631LSB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC
ATS632LSA 制造商:Allegro MicroSystems 功能描述:Zero-Speed, Self-Calibrating, Non-Oriented, Hall-Effect Gear-Tooth Sensor Module
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*