- 您現在的位置：買賣IC網 > PDF目錄375377 > ATS625LSG (Allegro MicroSystems, Inc.) True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor PDF資料下載
參數資料
| 型號： | ATS625LSG |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor |
| 中文描述： | 真零高速低抖動高精度齒輪齒傳感器 |
| 文件頁數： | 18/21頁 |
| 文件大?。?/td> | 625K |
| 代理商： | ATS625LSG |
18
ATS625LSG-DS, Rev. 1
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor
ATS625LSG
The device must be operated below the maximum junction
temperature of the device, T
J(max)
. Under certain combinations of
peak conditions, reliable operation may require derating sup-
plied power or improving the heat dissipation properties of the
application. This section presents a procedure for correlating
factors affecting operating T
J
. (Thermal data is also available on
the Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
θ
JA
, is a figure of merit sum-
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity,
K, of the printed circuit board, including adjacent devices and
traces. Radiation from the die through the device case, R
θ
JC
, is
relatively small component of R
θ
JA
. Ambient air temperature,
T
A
, and air motion are significant external factors, damped by
overmolding.
The effect of varying power levels (Power Dissipation, P
D
), can
be estimated. The following formulas represent the fundamental
relationships used to estimate T
J
, at P
D
.
P
D
= V
IN
×
I
IN
(1)
T = P
D
×
R
θ
JA
(2)
T
J
= T
A
+
T
(3)
For example, given common conditions such as: T
A
= 25°C,
V
IN
= 12 V, I
IN
= 4 mA, and R
θ
JA
= 140 °C/W, then:
P
D
= V
IN
×
I
IN
= 12 V
×
4 mA = 48 mW
T = P
D
×
R
θ
JA
= 48 mW
×
140 °C/W = 7°C
T
J
= T
A
+
T = 25°C + 7°C = 32°C
A worst-case estimate, P
D(max)
, represents the maximum allow-
able power level, without exceeding T
J(max)
, at a selected R
θ
JA
and T
A
.
Example
: Reliability for V
CC
at T
A
=
150°C, package SG, using
minimum-K PCB.
Observe the worst-case ratings for the device, specifically:
R
θ
JA
=
126°C/W, T
J(max)
=
165°C, V
CC(max)
=
26.5
V, and
I
CC(max)
=
8
mA. Note that I
CC(max)
at T
A
=
150°C is lower than
the I
CC(max)
at T
A
=
25°C given in the Operating Characteristics
table.
Calculate the maximum allowable power level, P
D(max)
. First,
invert equation 3:
T
max
= T
J(max)
– T
A
= 165
°C
–
150
°C = 15
°C
This provides the allowable increase to T
J
resulting from internal
power dissipation. Then, invert equation 2:
P
D(max)
=
T
max
÷ R
θ
JA
= 15°C ÷ 126 °C/W = 119 mW
Finally, invert equation 1 with respect to voltage:
V
CC(est)
= P
D(max)
÷ I
CC(max)
= 119 mW ÷ 8 mA = 14.9 V
The result indicates that, at T
A
, the application and device can
dissipate adequate amounts of heat at voltages
≤
V
CC(est)
.
Compare V
CC(est)
to V
CC(max)
. If V
CC(est)
≤
V
CC(max)
, then reli-
able operation between V
CC(est)
and V
CC(max)
requires enhanced
R
θ
JA
. If V
CC(est)
≥
V
CC(max)
, then operation between V
CC(est)
and
V
CC(max)
is reliable under these conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| ATS625LSGTN | True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor |
| ATS632LSA | ZERO-SPEED, SELF-CALIBRATING, NON-ORIENTED, HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS632LSC | ZERO-SPEED, SELF-CALIBRATING, NON-ORIENTED, HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS636LSE | Programmable Back Biased Hall-Effect Switch with TPOS Functionality |
| ATS635LSE | Programmable Back Biased Hall-Effect Switch with TPOS Functionality |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS625LSGTN | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS625LSGTN-T | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS625LSGTN-T3 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:True Zero-Speed Low-Jitter High Accuracy Gear Tooth Sensor |
| ATS627LSG | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:True Zero Speed, Low Jitter, High Accuracy Position Sensor IC |
| ATS627LSGTN-T | 功能描述:IC HALL EFFECT GEAR SENSOR 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
發布緊急采購，3分鐘左右您將得到回復。