- 您現在的位置：買賣IC網 > PDF目錄375377 > ATS610LSA (Allegro MicroSystems, Inc.) DYNAMIC, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSORS PDF資料下載
參數資料
| 型號： | ATS610LSA |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | DYNAMIC, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSORS |
| 中文描述： | 動態，峰值檢測，差分霍爾效應齒輪齒傳感器 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 182K |
| 代理商： | ATS610LSA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
ATS610LSA
AND
ATS611LSB
DYNAMIC, PEAK-DETECTING,
DIFFERENTIAL HALL-EFFECT
GEAR-TOOTH SENSORS
13
www.allegromicro.com
APPLICATIONS INFORMATION — Continued
Capacitor Requirements.
The choice of the capacitor at
pin 3 (C3) defines the minimum operating speed of the
target. This capacitor (0.1
μ
F minimum) is required to
stabilize the internal amplifiers as well as to eliminate the
signal offsets. Typically, a 0.33
μ
F low-leakage ceramic
capacitor is recommended. Values greater than 0.47
μ
F
should not be used as this may cause high-speed perfor-
mance degradation.
Capacitor leakage current at pin 3 will cause degrada-
tion in the low-speed performance of the device. Excess
capacitor leakage can result in the sensor changing output
state without movement of the gear tooth being sensed.
In addition to the capacitor leakage, it is extremely impor-
tant to minimize the leakage at the PC board and between
the pins of the sensor. Up to 50 nA of external leakage
can be tolerated at the capacitor pin node to ground.
Choice of low-leakage-current potting compounds and the
use of clean PC board techniques are extremely impor-
tant.
Operation From an Unregulated Power Supply.
In
automotive applications, where the device receives its
power from an unregulated supply such as the battery, full
protection is generally required so that the device can
withstand the many supply-side transients. Specifications
for such transients vary between car manufacturers, and
protection-circuit design should be optimized for each
application. In the circuit below, a simple
Zener-controlled regulator is constructed using discrete
components. The RC low-pass filter on the supply line
(R1C1) and a low-value supply bypass capacitor (CS) can
be included, if necessary, so as to minimize susceptibility
to EMI/RFI. The npn transistor should be chosen with
sufficiently high forward breakdown voltage so as to
withstand supply-side transients. The series diode should
be chosen with sufficiently high reverse breakdown
capabilities so as to withstand the most negative tran-
sient. The current-limiting resistor (RZ) and the Zener
diode should be sized for power dissipation requirements.
3
X
X
+
-
1
2
4
Vcc
Dwg. EH-008A
20
R 1
R
0.033
μ
F
0.22
μ
F
C
100 pF
OUTPUT
SUPPLY
0.033
μ
F
C S
2.5 k
6.8 V
C
C
R Z
Additional applications Information on gear-tooth and
other Hall-effect sensors is provided in the Allegro Elec-
tronic Data Book AMS-702 or Application Note 27701.
相關PDF資料 |
PDF描述 |
|---|---|
| ATS610LSC | DYNAMIC, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS611LSB | Dynamic, Peak-Detecting,Differential Hall-Effect Gear-Tooth Sensor(動態，峰值檢測，差分霍爾效應齒輪嚙合傳感器) |
| ATS611 | TRUE ZERO-SPEED, HALL-EFFECT ADAPTIVE GEAR-TOOTH SENSOR |
| ATS660LSB | TRUE ZERO-SPEED, HALL-EFFECT ADAPTIVE GEAR-TOOTH SENSOR |
| ATS612LSB | DYNAMIC, SELF-CALIBRATING, PEAK-DETECTING, DIFFERENTIAL HALL-EFFECT GEAR-TOOTH SENSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS610LSC | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:ZERO-SPEED, SELF-CALIBRATING, NON-ORIENTED, HALL-EFFECT GEAR-TOOTH SENSOR |
| ATS611 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:TRUE ZERO-SPEED, HALL-EFFECT ADAPTIVE GEAR-TOOTH SENSOR |
| ATS611LSB | 制造商:Allegro MicroSystems LLC 功能描述:Hall Effect Sensor 25mA 4-Pin SIP Module(SB) |
| ATS-61270D-C1-R0 | 功能描述:散熱片 FANSINK ASSY 26.25X26.25X9.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-61270K-C1-R0 | 功能描述:散熱片 FANSINK ASSY 26.25 X 26.25 X 14.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
發布緊急采購，3分鐘左右您將得到回復。